632651

Ferm TDM1025 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
EN
6 Ferm
Wear eye and ear protection.
During use the following points must be
considered:
• Donotremoveanymechanicalorelectrical
protective provisions.
• Checkwhetheralltheprotectiveprovisions
are in place and have been attached correctly.
• Wearsafetygogglesduringdrilling.
• Ifyouhavelonghair,besuretowearhair
protection (hair net or cap). Long hair can
easily be caught in moving parts.
• Wearfittedclothing;tiebuttonsonsleeves.
• Donotholdanyworkpiecesinyourhands
when drilling. Always use a machine clamp or
another clamping tool.
• Protectworkpiecesandclampingtoolsonthe
bench to prevent them from getting caught.
Fasten them yourself with screws or clamp
them to a machine clamp fastened to the
table.
• Checkwhetherthedrillholderistightened
properly.
• Checkwhethercablelead-throughsareokay.
• Toremovedrillchipsonlyusehandbrushes,
brushes, rubber wipers, chip hooks or similar
aids.
• Donotcarryoutanycleaningorgreasingwork
while the machine is in operation.
• AlwayskeepV-beltscovered(sothatyour
hands cannot become caught).
• Onlytightenthetoothedringdrillholderby
means of the wrench.
• Neverleavethewrenchofthedrillholderin
the drill holder! Before switching on the
machine, check whether the wrench really has
been removed!
• Donotuseanydrillswhicharedamagedon
the shank.
• Drillisnotsuitabletouseaspress!
• Ifthemainscableisdamaged,itmayonlybe
replaced by a mains cable of the same type.
Laser beam.
Never look into the light beam
Laser Class 2
from DIN EN60825-1:2007;
Ï: 650 nm; P ≤ 1mW
Additional safety warnings for lasers
• Do not look directly into the laser beam.
• Do not point the laser beam humans or
animals.
• Do not point the laser beam at strongly
reflecting material.
• Do not insert hard objects into the laser optics.
• Clean the laser optics with a soft, dry brush.
• Only have the laser repaired by a qualified
technician.
Immediately switch off the machine when:
• Interruptioninthemainsplug,mainsleador
mains lead damage.
• Defectswitch.
• Smokeorstenchofscorchedisolation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
The machine is provided with a zero
voltage switch. After the tension drops
the machine will not start to run
automatically for safety reasons. The
machine must be switched on again.
Replacing cables or plugs
Immediatelythrowawayoldcablesorplugswhen
theyhavebeenreplacedbynewones.Itis
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
Only use an approved extension cable suitable for
the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. Assembly
Fig. B
• Placethefootplate(13)inthecorrectposition.
• Fastenthecolumn(11)withtheboltssupplied
(12) to the footplate.
• Nowslidethetableholder(10)withthetable
over the column (11). With the fastening
handle (6) the table is fastened into the
desired position.
• Nowyoucanassemblethemachinecasing
(7) and lock with the locking pins (8).
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm TDM1025 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TDM1025 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info