Manual Ferm TCM1011 (page 5 of 56) (English, German, Dutch, French, Italian, Spanish)

510126

Zoom out

Zoom in

1/56

Installing the tile cutter

• The tile cutter may only be used as a fixed tool

and should be screwed down to a level and

horizontal surface. Please use the screw holes

in the base of the machine.

• The electrical supply must be connected to a

230 V earthed wall socket. The mains voltage

must comply with the information on the type

plate, and must be protected by a circuit breaker.

• Do not use the power cable to pull the plug

from the socket. Protect the cable against

heat, oil and sharp objects.

Only use accessories and auxiliary

equipment mentioned in the instructions

for use or recommended or mentioned by

the manufacturer. Using other

accessories or auxiliary equipment may

carry a risk of injury for you and others.

4. OPERATION

Operation

Fig.1

• Before starting the job, please ensure there is

sufficient water in the water tray (4) i.e. the

diamond blade runs through the water. During

the job, the water tray must be topped up.

• Do not start working before the maximum

speed has been reached.

• The diamond blade must NEVER be exposed

to sideways pressure; they can break and the

flying pieces become projectiles!

• Do not attempt to cut extremely small pieces

from the tiles. Always make sure that the full

surface of the tile is on the work table. The

supplied mitre guide can be used to push the

tiles through the cutter. In the early stages of

cutting in particular, the tile must remain

absolutely level to avoid the tile moving up.

• Do not overload your tool. It is better and safer

to work within the indicated power range. Do

not cut materials other than tiles.

• Maintain your tools carefully. Keep the tools

sharp and clean in order to work properly and

safely.

• Follow the maintenance instructions and the

instructions for replacing the diamond blade.

• Stand safely and maintain your balance. Avoid

any unnatural body angles. Remain alert and

pay attention to your work. Use common

sense. Do not use the machine when you

cannot concentrate or when you are tired.

Full-length adjustable fence

Fig.1

The fence (3) enables you to cut parallel to the

cutting blade. Set up: Loosen the knobs (7) and

set the required distance. Tighten the knobs on

both sides of the work table. The markers

determine the measurements (8).

Mitre guide

Fig.1

The mitre guide has a variable setting between 0°

and 45°. Loosen the knobs (5), set the mitre by

tilting the table (1) up until you have reached the

required tilt. Tighten the knobs (5) again on both

sides of the work table.

Checking and replacing the diamond blade

Fig.1 + 2

• Cracked or distorted diamond blades must be

replaced.

• Type of disk: a diamond blade with a diameter

of 180mm.

• Do not use diamond blades that do not meet

the specifications in these instructions.

• Ensure that the diamond blade is secured

properly and rotates in the correct direction.

• To replace a worn disk, please take the

following steps (Fig. 2).

Disconnect the plug from the socket.

• Remove the water tray (4, Fig. 1) from the

machine.

• Loosen the splash guard’s fixing bolts and

remove the splash guard.

• Loosen the blade fixing nut (4, Fig. 2).

• Remove the counter flange (3, Fig. 2) and

blade (2, Fig. 2) and push the new blade on

the flange (1, Fig. 2). Consider the rotation

direction indicated on the blade. Attach the

counter flange (3, Fig. 2).

• Tighten the fixing nut (4, Fig. 2) and the splash

guard.

• Ensure you do not leave any tools lying on the

splash guard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TCM1011 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm TCM1011

Ferm TCM1011 User Manual - English, German, Dutch, French, Spanish - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TCM1011 Manual

Product: