Manual Ferm SGM1008 (page 6 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510105

Zoom out

Zoom in

1/96

to be sprayed are free from dust, dirt and grease.

Make sure that you have masked the areas that

should not be sprayed, using a good quality



should be thoroughly mixed and free from lumps

or other particles. Many substances can be

sprayed with your spray gun, but always check

the manufacturers recommendations before

purchasing your paint.

Thinning

Always remember to disconnect from

the mains supply before lling the paint

container with sprayable material.

Most paints are supplied ready for brush

application and will need to be thinned before

they are suitable to be sprayed. Follow the

manufacturers advice on thinning the paint when

used with a spray gun. The viscosity cup will help

you to determine the correct viscosity of paint to



cup to the brim with the paint. Measure the

amount of time it takes for the cup to empty back

into the can.

The table below shows recommended times for

different types of material.

Plastic & latex paint 24 - 28 seconds

Water based paint 20 - 25 seconds

Primers 24 - 28 seconds

Varnishes 20 - 25 seconds

Oil based paints 18 - 22 seconds

Enamel paints 18 - 22 seconds

Aluminium paints 22 - 25 seconds

Car undersealing 25 - 35 seconds

Wood sealers 28 - 35 seconds

Wood preservatives No thinning required

Wood stains No thinning required



time to empty, then further thinning is required.

Mix in a small quantity of the appropriate thinner

and use the viscosity test until the correct

thickness is achieved. Some sprayable materials

contain particles and lumps. These materials



container.



Fig. C

Fill the paint container with the correctly thinned

and strained paint. Connect the spray gun to the

mains supply. Aim the spray gun at a piece of

scrap material and operate the trigger switch until

paint is spraying. Adjust the output control (2) until

the required volume of paint is spraying. Turn the

output control in a clockwise direction (B) to





affect the spray pattern. A poor spray pattern will

concentrate the paint in the centre of the spray



give even distribution of paint throughout the

pattern.



Fig. D

To obtain the best results, keep your spray gun



the nozzle 25 - 30 cm from the surface and spray



spray at an angle as this will lead to paint runs on



spraying large areas, use a criss-cross pattern as

shown.

Fig. E

Never start or stop the spray gun while it is aimed

at the surface to be sprayed. Evenly control the

speed of movement of the spray gun. A fast

speed of movement over the surface will give a

thin coat and a slow speed will give a heavy coat.



required, make sure you observe the manu-

facturers drying time recommendations before

applying a second coat. When spraying small

areas, keep the output control on a low setting.

This will avoid using too much paint and prevent

overspray. Where possible, avoid stopping and

starting when spraying an object. This can lead to







Fig. F













and tighten.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1008 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm SGM1008 Manual

Product: