Manual Ferm SGM1006 (page 3 of 32) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510102

Zoom out

Zoom in

1/32

Ferm

MULTIPURPOSE GAS SOLDERING

TOOL

The numbers in the following text correspond

with the pictures at page 2

Features

1. Switch

2. Shut off lever

3. Nut

4. Soldering head

5. Filling valve

6. Flow control knob

7. Ignition button

8. Guard

9. Standard tip

10. Diagonal tip (3 mm)

11. Chisel tip (3,5 mm)

12. Hot knife

13. Hot blower

14. Reflector

15. Wrench (7 mm)

16. Wrench (8 mm)

Warnings

• Donotfillgasorstorenearopenflame,heater

or combustible materials

• Useonlyhighqualitybutanegas

• Butanegasishighlyflammable,pleasehandle

with care

• Donotdrop,puncture,orincinerate

• Donotstoreoroperateinaplacewherethe

temperature is above 50º C (122º F)

• Keepoutofreachofchildren

• Cooldownbeforeputtingprotectivecapon

and before storing

Gas filling and refilling

• Ensuretheswitch(1)isturnedtotheOFF

position before filling

• Reversetheunit;insertthegascontainer’s

nozzleverticallyintofillingvalve(5)

• Whengasescapesfromfillingvalve,remove

the nozzle from the filling valve

Ignition

• Movetheflowcontrolknob(6)tothemiddle

position

• Movetheswitch(1)upwardandtotheright

• Pressdowntheignitionbutton(7)tolightup

the open flame

• Whentheunitisworkingasasolderingtool,3

seconds after lighting the torch, please move

the shut off lever (2) to the left and release it.

Thentheopenflamewillbeshutoffandyou

will find the soldering head (4) becomes red.

Shutting off

Movetheswitch(1)upwardsandtotheleft.The

switchwillreturntoOFFposition.

Flame lengt or temperature adjustment

After ignition, turn the flow control knob (6) to the

right to increase the flame length of the torch or

the temperature of soldering tip or hot air, to the

left to decrease the flame length or the

temperature.

Operating tips

• Afterfillingorrefillingwithgas,waitfor

approximately2minutessothatthegasinthe

cylindercanbestable.

• Solderingtipsmustbetin-platedbeforeusing

themforthefirsttime.Athinlayerofsolder

should be applied to the tip when it has been

heated.

• SolderingshouldNOTbecarriedouton“live”

circuits, as this soldering unit does not

possessanyspecialelectricalinsulation

• Keepyoursolderingspongemoist

How to fit or replace different

accessoires

Always allow unit to cool before removing

or replacing tips

Replace soldering tips

• With7mmwrench(15)onthesolderingtipor

hot blow head (9 till 14) and 8 mm wrench on

thesolderinghead(4),youcantightthetipor

hot blow head or unscrew them.

• Whenyouunscrewthenut(3),youcan

remove the guard (8) and soldering head (4).

Now the unit becomes an open flame torch.

Troubleshooting

1. Does not ignite

• Emptygas

• Refill butane gas

• Gas pressure too high or too low

• Slide flow control knob (6) to lower or higher

position

2. Torch flame has no proper power

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm SGM1006 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm SGM1006 Manual

Product: