383724

Ferm rsm1015 Manual

6
Zoom out
Zoom in
Previous page
1/104
Next page
6
EN

Mounting
● Open the collar (10) by turning it
counterclockwise.
● Insert the saw blade (11) in the saw blade
holder (4) as far as possible. The teeth of the
saw blade (11) must point downward and
forward.
● Close the collar (10) by turning it clockwise.
Removing
● Open the collar (10) by turning it
counterclockwise.
● Remove the saw blade (11) from the saw
blade holder (4).
● Close the collar (10) by turning it clockwise.
USE

● To switch on the machine, keep the lock-off
button (2) pressed and simultaneously press
the on/off switch (1).
● To switch off the machine, release the on/off
switch (1).

The release button for the auxiliary grip can be
set to 4 positions.
2
Do not set the auxiliary grip during use.
● Slide the release button (3) in the direction of
the main grip (7).
● Turn the auxiliary grip (8) to the required
position.
● Release the release button (3).

The saw shoe can be adjusted in order to rest
properly on the workpiece.
2
Do not adjust the saw shoe during use.
● Release the adjustment handle (6) by lowering
it to the open position.
● Move the saw shoe (5) to the required
position.
● Lock the adjustment handle (6) by raising it to
the closed position.
Plunge cutting
● Only use ‘plunge cutting‘ on soft materials.
● Only use ‘plunge cutting‘ with short saw blades.
● Switch on the machine.
● Wait until the machine has reached full speed.
● Place the saw shoe on the workpiece.
Make sure that the bottom edge of the saw
shoe rests on the workpiece.
● Slowly move the saw blade into the workpiece
at an angle. Move the machine to the vertical
position and continue to move the saw blade
along the pre-drawn line.
● Switch off the machine when the work has
been completed.
● Remove the machine from the workpiece.
Flush cutting
● Only use ‘ush cutting‘ with elastic, bi-metal
saw blades to use the machine on protruding
objects close to the wall.
● Switch on the machine.
● Wait until the machine has reached full speed.
● Place the saw blade directly on the wall.
Slightly bend the saw blade to make sure that
the saw shoe rests against the wall.
● Slowly move the saw blade through the
workpiece. Apply constant lateral pressure
against the wall.
● Switch off the machine when the work has
been completed.
● Remove the machine from the workpiece.
Hints for optimum use
● Clamp the workpiece. Use a clamping device
for small workpieces.
● Draw a line to dene the direction in which to
guide the saw blade.
● Hold the machine with both hands.
● Set the auxiliary grip.
● Adjust the saw shoe.
● Switch on the machine.
● Wait until the machine has reached full speed.
● Place the saw shoe on the workpiece.
● Slowly move the machine along the pre-drawn
line, rmly pressing the saw shoe against the
workpiece.
● Do not apply too much pressure on the
machine. Let the machine do the work.
● Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm rsm1015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm rsm1015 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info