539202

Ferm RSM1014 FPRS-1800 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
Ferm6
GB
Speed control
Fig. I
• Duringoperationandwhilstthemachine
is at rest the stroke rate (speed) can be
selected using the thumbwheel (6).
• Thestrokeraterequireddependsuponthe
material conditions. The optimal setting
should be determined in use.
• Afterworkingforlongerperiodsatlow
speed you should allow the machine to cool
down by running it at maximum speed with
no-load for approx. 3 minutes.
Sawing tips
• Adjustsawbladeandstrokeratetosuitthe
material to be processed. For right radius
curves it is best to use a narrow saw blade.
Apply coolant or lubricant to deal with the
utteringproducedalongthecutlinewhen
sawing metal.
• Checkwood,chipboards,building
materials etc, for foreign bodies (nails,
screws etc.), before sawing and remove
them, if necessary.
• Clampmaterialwell.Donotsupportthe
workpiece with hand or foot. Do not touch
objectsortheoorwiththesawrunning
(danger of backlash).
• Putthefootplateonthesurfaceofthe
workpiece, and saw through it with constant
contactpressureorfeed.Ifthesawblade
seizes switch the machine off immediately.
Spread the gap with a suitable tool and pull
out the saw blade.
• Afternishingwork,switchoffthemachine
and only put down after it has come to a
complete standstill.
Plunge cutting
Fig. E
• Plungecuttingmayonlybeusedonsoft
materials such as wood, aerated concrete,
gypsum plaster boards, etc.
• However,thisrequiresacertainpractise
and is only possible with short saw blades.
• Placethesawontotheworkpieceand
switch it on.
• Ensurethatthebottomedgeofthefootplate
rests on the workpiece surface as shown.
• Slowlysawintotheworkpieceatanangle,
moving the saw to a vertical position and
continue to saw along the cutting line.
• Switchthesawoffandliftofftheworkpiece
when the work is complete.
Flush sawing
• Elasticbi-metalsawbladesallowyouto
saw protruding objects (e,g, water pipes,
iron bars, etc,) nearby the wall.
• Applythesawbladedirectlytothewall
and bend slightly so that the footplate rests
against the wall.
• Switchthemachineonandsawoffthe
workpiece keeping constant lateral pressure
against the wall.
Rotatable handle
Fig. F
The handle can be rotated in 90° steps to the
machine housing. Slide the rotation button (3)
backwards and rotate the handle to the desired
position. Make sure the handle locks in position
before use.
LCD display
Fig. G
This machine is equipped with a LCD display.
• Toturnthedisplayon,pressthedisplay
button (10) once. To turn the display off,
press the display button again.
• Theclock(11)andminutes(12)remaining
icons indicate the number of minutes of
running time that are available before the
batteryrequiresrecharging(Lithium-Ion
battery only)
• Thebatteryicon(13)indicatesthe
amount of charge remaining in the battery.
Each charge bar displayed indicates
approximately 10% charge remaining in the
battery. A total of 10 charge bars indicates a
fully charged battery.
• Pressthebacklightbutton(14)toswitchthe
backlightofthedisplayon.Pressitagainto
switch the backlight of the display off.
Hex key storage
Fig. H
The included hex key can be stored in the
battery compartment.
5. SERVICE & MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work
on the motor.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm RSM1014 FPRS-1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm RSM1014 FPRS-1800 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info