Manual Ferm PWM1001 - AX-Power (page 8 of 60) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

800252

Zoom out

Zoom in

1/60

4. OPERATION

Connecting the water supply

This unit is to be used with acold-water

source only!

The pressure washer must only be used

with clean water; use of unfiltered water

or corrosive chemicals will damage the

pressure washer.

Ensure that you have asuitable water

supply to feed the pressure washer.

Check that all connections are tight and

there are no leaks in the hose.

You can enable the water supply via awater tank

(or pond, rain barrel, etc.) or via awater tap.

Water tank (water suction function)

Fig. 5A

Clean the suction filter (9) at regular

intervals, and check it for damage.

Otherwise, its function can be impaired.

When water is supplied via awater tank, pond,

rain barrel, etc. , the assembled suction hose (7)

must be used. Only clear fresh water may be used.

1. Connect the assembled suction hose (7) to the

pressure washer, place the hose connector (5)

on to the water inlet (4).

2. Lower the suction filter (9) into water. Ensure

there are no obstructions around the suction

filter (9). Move the float ball (8) in such away

that the suction filter (9) does not touch the

water bottom. The suction filter (9) must be

placed at least 20 cm from the water bottom to

prevent the suction of sand.

3. Check that the hose has no kinks in it.

4. The pressure washer is now ready for use.

Water tap

Fig. 5B

Use the device on adomestic water

connection with maximum pressure of

5bar.

The supply tap should be fully open.

1. Ensure that you have asuitable water supply

to feed the pressure washer.

2. Connect the water supply hose (not included)

to the water inlet (4).

3. Connect the water supply hose (not included)

to the water supply.

4. Turn on water and heck that the hose has no

kinks in it.

5. The pressure washer is now ready for use.

Switching the pressure washer on/off

Fig. 1

The motor of this pressure washer will

NOT run. It will only operate when the

trigger is squeezed.

Before starting make sure the pressure

washer is connected to awater source.

Dry running will damage the pressure

washer!

• To start the pressure washer, press and hold

the release button (11) and press the switch

lever (10).

• To stop the pressure washer, release the

switch lever (10).

Adjusting the nozzle (3)

Fig. 6

Water may be sprayed out of the nozzle (3) either

linearly or in afan shape. Turn on the pressure

first, and then adjust the nozzle (3).

Finish operation

Fig. 1

1. After use (when water is supplied via awater

tank, pond, rain barrel, etc.) allow the

pressure washer to run using clean water for

2 - 3 minutes in order to remove residues and

particles that may have accumulated in the

machine and hose. This is not necessary when

used with clean tap water.

2. To stop the pressure washer, release the

switch lever (10).

3. Turn off the water supply.

4. Remove the battery from the machine.

5. Press and hold the release button (11) and

press the switch lever (10) to depressurize and

drain the system.

6. Disconnect the hose from the pressure washer.

7. Wipe all surfaces of the unit and accessories

with adamp clean cloth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PWM1001 - AX-Power in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4.71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PWM1001 - AX-Power Manual

Product: