Manual Ferm PPM1010 (page 6 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510112

Zoom out

Zoom in

1/56

6 Ferm

• Start the machine by pressing the “lock off”

button (to disengage the switch) and switch on

the machine.

• The planer is now switched on and you can let

go of the release button.

• Always hold the planer with both hands on the

handles, so as to gain the best possible control

over your planing operations. Besides you do

not risk becoming in touch with the moving parts.

• When the machine has reached full speed it

can be pushed to the front over the work

piece. At the beginning of the planing

operation, put some pressure on the front and

at the end of the operation, on the rear of the

appliance. This results in the appliance

remaining flat on the work piece and prevents

the corners from getting rounded off.

• To obtain a level and smooth surface use a

greater planing depth when rough planing and

a lesser planing depth when planing a layer.

Hold the electric tool straight during the

operation, otherwise you will obtain an uneven

surface. After the operation switch off the

electric tool and remove the mains plug.

Bevelling edges

Fig. 1

The V-groove in the planer shoe allows easy

beveling of workpiece edges. Place the planer

with the V-groove (7) onto the edge of the

workpiece and guide along the edge.

Warning! Use spindle lock only in stand

still mode.

• Take care that your hand never comes in

contact with the work piece during the

operation.

• Only use the electric plane on the upper side

of the work piece, never from below or from

the side.

• Store the appliance only after it has come to a

complete standstill.

• Use a suction device to suck off wood

shavings or dust. For this use the connecting

pipe and connect a suction pipe to it.

• Use a holding device to work on small work

pieces.

Fitting the rip fence

Fig.4

• Loosen knob (9).

• Insert the rip fence into the slots provided.

• Set the correct cut width and tighten the knob

(9).

4. CARE & MAINTENANCE

Before undertaking any care or

maintenance always remove the mains

plug from the socket.

The planing tool becomes worn after a period of

operation. If you use a blunt or damaged planing

tool operational efficiency is reduced and the

electric motor might become overloaded. Check

the planing tool regularly with regard to wear or

damage. Depending on its condition, the planing

tool will have to be replaced.

Removal of plane blade

Fig. 3

Use the enclosed open-jawed spanner

(Accessories). First unscrew the three clamping

screws (6) with the open-jawed spanner and

remove the plane blade (3), the plane blade holder

(2) and the plane blade support (4) from the

holding shaft (1).

Installation of plane blade

Fig. 3

Take the new plane blade (3) and position it

between the plane blade support (4) and the plane

blade holder (2). Now turn the clamping screws (6)

as far as possible into the plane blade support. But

not so far that the plane blade and the plane blade

holder become detached again from the plane

blade support. Afterwards put the plane blade,

plane blade holder and plane blade support

together into the holding shaft. The plane blade

support, plane blade and plane blade holder will

now be fastened together in the holding shaft by

releasing the clamping screws with the open-

jawed spanner and thus the plane blade, plane

blade support and plane blade holder are clamped

in position.

Attention! Unscrew clamping screws as fas as

possible so that a sufficient attachment is ensured.

Warning!

• When installing and removing the plane blade,

care has to be taken that all parts (plane

blade, plane blade holder, plane blade support

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm PPM1010 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm PPM1010 Manual

Product: