697795
9
Zoom out
Zoom in
Previous page
1/108
Next page
9
EN
Note: Always replace both carbon brushes at the
same time, never use a mixture of old and new
brushes.
Mounting the dust bag
Fig. 1
Press in the clamp of the dust bag (13) and slide
it onto the opening on the back of the machine.
The dust bag stays in place when you release the
clamp.
4. OPERATION
Using the mitre saw
Fig. 1
Before use, always check for faults or
defects!
Set the desired sawing angle of the machine.
Put the plug into the socket.
Fix the piece of work in place using the clamp
(7): make sure that the material is well clamped
in place!
Hold the material tightly on the left side while
making sure that you keep a safe distance
from the blade of the saw.
To start the machine, press and hold the Lock-
off button (3) and press the on/off switch (1).
Make sure that the saw blade has reached full
speed before allowing it to touch the piece of
work to be sawn.
Now bring the saw slowly downwards so that
the saw blade saws through the piece of work
and passes through the slot in the table. Do
not put any pressure on the saw. Give the
machine time to saw through the piece of work.
Bring the machine gently up again and switch
it off by letting go of the switch (1).
Using the slide-function
Fig. 1
The machine must be firmly bolted to a
workbench.
Use the slide-function for sawing wide
workpieces:
Fix the piece of work in place using the clamp
Loosen the knob (12)
Slide the machine completely towards yourself
Turn on the machine using the switch
Bring the saw slowly downwards so the saw
blade saws through the piece of work
Push the machine slowly backwards
Bring the machine gently up again and switch
it off by letting go of the switch
Using the laser
Fig. 2
To switch on the laser, press the on/off switch 2.
To switch off the laser, release the on/off
switch 2.
Transport position
When moving the saw, make sure the saw is
in inward position. Check that all locks and
tensioning devices are secure:
Make sure the mitre angle is set to 0°
Make sure the bevel angle is set to 0°
Lock the Knob adjusting saw angle (9) by
turning it clockwise
Slide the machine completely towards yourself
Lock the sliding function by turning Kob over
sliding support (12) clockwise
Unlock the Lock pin (5) on the right hand side
of the machine
Push the machine completely downwards
Lock the Lock pin (5) on the right hand side of
the machine
Only lift the machine by the solid underside of the
machine. Do not lift the saw by the switch handle.
5. SERVICE AND MAINTENANCE
Always make sure that the machine is
not connected to the mains electricity
when you carry out any maintenance of
the mechanism.
Slide rails
Dirt can damage the slide rails and thereupon the
operating of the machine.
Clean the slide rails regularly with a soft cloth.
Drip some lubricating oil on the slide rails
Move the mitre saw forwards and backwards
so the oil spreads over the complete rails
These machines are designed to function for a
long time without any problems with a minimum
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1039 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1039 in the language / languages: All languages as an attachment in your email.

The manual is 8,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info