Manual Ferm MSM1033 (page 11 of 56) (English, German, Dutch, French, Spanish)

510117

Zoom out

Zoom in

1/56

Ferm

• Hold the handgrip (2) firmly and move the

turntable to the left or right. The entire saw

moves in the direction required.

• Then screw the two screws tight again.

• The turntable clicks into place at the following

angles: 0º, 15º, 22,5º, 30º, and 45º (both left

and right).

b. Table Saw

See: Parallel and mitre guide (table saw)

Set the guide for mitre sawing and follow the

procedure under ‘Using the table saw’.

Bevelling

(Mitre saw/table saw)

When bevelling the piece of work is sawn at an

angle to the vertical.

The bevel angle is a maximum of 45º.

• Unscrew the knob (6).

• Set the required bevel angle using the scale

(7).

• Screw the knob tight again.

Double mitring (mitre saw)

When double mitring the piece of work is placed

against the stop and sawed across its breadth in

both mitring and bevelling cutting directions.

• Set the mitring angle.

• Set the bevelling angle.

• Follow the procedure under ‘Using the mitre

saw’.

Note: With double mitring the saw blade

is more exposed because of the large

angle. So there is a greater chance of

injury. Keep your hands a good distance

from the saw blade!

Problems

The motor does not start

• The plug is not in the socket

• The power cord is broken

• The switch is defective. Take the machine to

your Ferm dealer for repair.

The fuse is burnt out:

• Remove the plug from the socket.

• Remove the cap (nr. 31 on Fig.1) from the fuse

box with help of a screwdriver

• Check the fuse and replace when necessary.

Always replace the fuse by a new one with the

same specification.

• Mount the cap on the fuse box again.

The saw cut is not even (jagged)

• The saw blade must be sharpened

• The saw blade is mounted back to front

The saw blade is clogged with resin or

sawdust

• The saw blade is not suitable for the piece of

work being used

The motor has difficulty in reaching full speed

• The extension cable is too thin and/or too long

• The mains voltage is less than 230 V.

The machine vibrates excessively

• The saw blade is damaged

• The machine is not fixed to the workbench

The machine becomes excessively hot

• The ventilation slots are blocked. Clean them

out with a dry cloth.

5. Service and maintenance

Maintenance

Always make sure that the machine is not

connected to the mains electricity when

you carry out any maintenance of the

mechanism.

Ferm machines are designed to function for a long

time without any problems with a minimum of

maintenance. By cleaning the machine regularly

and using it in the correct way you can contribute

to a long life of your machine.

Transport

• Check that all locks and tensioning devices

are secure.

• Carry the machine with both hands under the

lower bench surface when the machine must

be moved.

Cleaning

Clean the machine housing regularly with a soft

cloth, preferably after each time you use the

machine. Make sure that the ventilation slots are

free of dust and dirt. For stubborn dirt use a soft

cloth dampened with soapy water. Never use

solvents such as benzene, alcohol, ammonia, etc.

These types of solvents can damage the plastic

parts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1033 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1033 Manual

Product: