Manual Ferm MSM1033 (page 8 of 56) (English, German, Dutch, French, Spanish)

510117

Zoom out

Zoom in

1/56

8 Ferm

use a damp cloth for cleaning.

38. Do not use saw blades which are damaged or

deformed.

39. Replace table insert when worn.

40. Use only saw blades recommended by the

manufacturer.

41. Take care that the selection of the saw blade

depends on the material to be cut.

42. Connect circular saws to a dust-collecting

device when sawing.

43. Use and correct adjustment of the riving knife

44. Use and correct adjustment of the upper saw

blade quard.

45 The dust that is emitted when sawing certain

types of wood can be toxic, i.s. oak, birch, ash,

beech and fibreboard. Certain dust, from

tropical wood types such as rosewood, coco

bolo and afzelia, cause cancer when breathed

in regularly. Ensure therefore that you have

good dust suction installed with a device that

fulfils the following requirements:

• Tube must fit perfectly on the connection

element

• Suction volume must be larger than 550 m3

per hour

• Vacuum at connection more than 740 Pa

• Air speed at connection more than 20 meters/

second

Ensure that the least possible wood dust is

released in the atmosphere. WIPE wood dust

away (do not blow away with pressured air),

repair leaks in the tubes and ensure

appropriate ventilation.

Do not use saw blades which are damaged or

deformed.

Always clamp or press the workpiece firmly

against the saw guide, before you carry out

the process.

Do not modify the machine; unauthorised

parts have not been tested and approved.

Mainly use:

• No unauthorised saw blades

• No unauthorised safety systems 7

• Always use the supplied safety systems!

• Always use a cavity blade for scalloping.

46 Wear ear protectors. The following facors can

be of influence in producing noise

• The kind of material to be cut

• The sawblade

• The force of which the workpiece is fed

Loud noise can lead to hearing damage.

Ensure that you wear ear protectors.

Ensure that the cavity blade is not bent,

this can also cause noise.

47 Residual risks

The following risks are inherent to the use of

these machines:

• Injuries caused by touching the rotating parts

• Injuries caused by disruption of the cutting

blade

• These risks are most evident:

• Within the range of operation

• Within the range of the rotating machine parts

In spite of the application of the relevant

safetyregulations and the implementation of

safety devices, certain residual risks cannot

be avoided. These are:

• Impairment of hearing.

• Risk of accidents caused by the uncovered

parts of the rotating cutting blade.

• Risk of injury when changing the blade.

• Risk of squeezing fingers when opening the

guards.

3. Assembly and accessories

Installation of the mitre saw

• Place one extension piece on the right-hand

side of the machine and the other extension

piece on the left-hand side of the machine.

• Loosen the locking bolts and slide the guide

rods in the openings.

• Tighten the locking bolts again.

• Place the work piece clamp on the left or right

side of the machine.

• Hold the handgrip and move the saw slightly

downwards and then pull the pin out slightly so

that the machine comes free.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Mounting the support bracket.

• Mount the support bracket into the slot in the

rear of the base.

• Tighten the screw to secure the support

bracket.

Installation of the machine on a workbench or

on the subframe.

This machine is a stationary machine and for

safety reasons must always be firmly installed and

not used for mobile applications.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1033 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm MSM1033 Manual

Product: