634074
6
Zoom out
Zoom in
Previous page
1/30
Next page
Ferm 55
Turn the handle of the turntable counterclockwise
Slide the machine completely towards yourself
Turn the handle of the turntable clockwise to lock
the slide-function
Unlock the pin on the right hand side of the machine
Push the button in the handgrip to unlock the saw
blade protection
Push the machine completely downwards
Lock the pin on the right hand side again
Only lift the machine by the solid underside of the
machine.
WHILE THE MACHINE IS IN USE
With frequent use of the machine, do not let routine lead
to mistakes. Remember that a slight lack of
concentration can lead to serious injuries in a fraction of
a second.
Before beginning to saw, make sure that the
protective hood is in the right position.
Before cutting the first cut, let the machine run for a
short while. If you hear any unusual sounds or
observe any strong vibration, turn the machine off
and take the plug out of the socket, and then find the
cause of the problem. Do not switch the machine on
again until the cause has been found and the fault
repaired.
Make sure that the piece of work being sawn off does
not get stuck in place, do not hold it or clamp it and
no not secure it against the stop. It must be able to
move freely along the side of the saw blade. When
this is not possible the piece of work being sawn can
be trapped by the saw blade and be flung about.
Avoid placing your hands anywhere where in the
case of a sudden movement one or both hands can
come into contact with the saw blade.
Let the saw get up to full revolutions before you start
sawing.
Press the saw head downwards so that the motor is
not overloaded and the saw blade does not get
jammed.
If you need to remove jammed material, first let the
saw blade stop turning completely, switch the motor
off and take the plug out of the socket.
At the end of the sawing process, keep the saw head
downwards, switch off the machine and wait until all
moving parts has come to a stop before you take
your hands off the machine.
MOTOR
Connect the machine to a 220/230 V~ socket.
If the motor does not start, immediately release the
switch. Take the plug out of the socket. Check that
the saw blade can turn freely. If so, try starting the
machine again.
To prevent damaging the motor must be regularly
freed of chips and dust to ensure correct cooling.
If the motor suddenly stops while sawing, let go of
the switch immediately. Loosen the saw blade from
the piece of work, after which sawing can continue.
Using long cables of too small a diameter can result in
loss of voltage, which can lead to problems with the
motor.
For a length up to 15 metres a cable must be used
with a diameter of 1.5 mm
2
.
For a length of between 15 and 40 metres a cable
must be used with a diameter of 2.5 mm
2
.
3. ASSEMBLY AND ACCESSORIES
CHANGING THE SAW BLADES
Fig. 3
Only use saw blades that are sharp and
undamaged. You must immediately replace
chipped or bent saw blades.
Lock the machine in its highest position
Remove the screw (20) by turning it
counterclockwise
The guiding strip (21) is now mounted on only one
side
Unscrew the 4 screws (23) indicated in the drawing
(fig. 3). The guard is now only connected with one
point (24) and can be moved forward.
Press the spindle lock (22) and turn the spindle until it
engages in the lock. Keep the spindle lock pressed
during this procedure.
Remove the saw blade bolt (18) by turning it
counterclockwise
Remove the flange (19)
Replace the saw blade: the arrow on the blade
pointing clockwise
Mounting flange, cover, guiding strips and screw
again
Check if blade protective cover works correctly
Never use the mitre saw without safety guard!
ADJUSTING THE SAW ANGLE
Fig. 2
Turn over the knob (9).
Turn the machine to the desired angle (the angle can
be read off on the front of the machine).
Turn over the knob (9).
SETTING UP THE DOUBLE SAWING ANGLE
/ MITRING
Fig. 2
Adjust the first angle as described for adjusting the
saw angle (above).
Turn the knob (12) anticlockwise and then set the
angle desired (you can read this off on the back of the
machine. Then tighten the knob (12) again by turning
it clockwise.
CHANGING THE CARBON BRUSHES
Fig. 2
Make sure that the plug is not in the socket!
Unscrew the covers (4) with a flat bladed
screwdriver. Remove the carbon brushes with the
same type of brushes. Screw the covers (4) tight
again.
6 Ferm
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm MSM1017 - FKZ-305R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm MSM1017 - FKZ-305R in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info