Manual Ferm LHM1011 (page 6 of 32) (English, German, Dutch, French, Spanish)

510137

Zoom out

Zoom in

1/32

mains voltage is not suitable they should be

checked by a skilled electrician.

• Your socket plug must be grounded and your

electric system must be supplied with an earth

leakage circuit breaker.

• Keep children and other unauthorized

persons away from the machine.

• Protect the machine from frost and low

temperatures.

• In case the machine cannot hoist a load, do

not keep pressing the hoisting pushbutton, to

avoid damaging the machine. It means that

the load exceeds the machine maximum

capacity.

• The machine shall not be disassembled when

running or connected to power.

• The machine shall not be operated when it is

raining or storming.

Do not stand under hoisted weights!

• Before starting the work, make sure that the

steel cable is correctly winded around the reel

and the pitch is equal to the cable diameter

(Fig. 2).

Observe the maximum load indicated on

the hoist, not that on the hook!

• Do not lift loads bigger then the rated load of

the hoist.

• Leave at least three turns of cable around the

reel, so that the cable connection is not under

stress.

• If the red cable appears do not continue to

unroll it.

• To avoid any danger, do not wind more than

15 m of cable around the reel.

• In case the steel cable is worn out, it must be

replaced only with a cable of same features

manufactured by us. It can be found at all

authorized service shops.

• Before starting the work, check that switches

are in good operating conditions.

• In case the hoist stops during the lowering of

a load, it is normal that the load goes down a

few millimeters more because of the inertial

force.

• Never pull or push laterally the cable or the

load.

• Transport of people with the hoist is forbidden.

• Avoid switch-on / switch-off quickly

sequences.

• Wear gloves during transport.

Attention! The hoist electric motor is not

supplied with any mechanical overload

cut-out (to avoid an unexpected and

unwanted restart). Therefore, if you are

unable to hoist a load, do not insist and

let the motor cool down.

3. Installation

Mounting

Fig. 4

The hoist is provided with a bracket system which

allows holding rectangular beams. The beam

dimensions must be in accordance with the

distance between the hoist and the hinge and the

load to be hoisted. We recommend contacting

a skilled technician for help and checking the

solidity of the beam construction. The bolts must

be properly tightened. Before the start-up a skilled

technician should check that the support and the

coupling of the hoist are well sized.

Pulley block

Fig. 5 + 6

The lever hoist is provided with an extra pulley

and hook. When used correctly, the machine can

hoist double load. Assemble the pulley with help

of the bolts as shown in the picture. Tighten the

two bolts completely, and then unscrew them for

of turn.

The fixed hook on the machine can be attached

on the cover: there is a special hole for that

purpose. The load is now lifted with help of 2 steel

cables: the machine can hoist a double load.

4. Use

Remove the adhesive tape from the

cable reel before using the machine.

Secure the load carefully to the lever

hoist.

Do not lift loads bigger then the rated

load of the hoist.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm LHM1011 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm LHM1011 Manual

Product: