Manual Ferm JSM1019 FPJS-1800LK (page 8 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

539086

Zoom out

Zoom in

1/60

8 Ferm

Adjusting the bottom plate

Fig. C + D

Adjust the angle of the bottom plate as follows:

A. Loosen the socket head screws with the Allen

key supplied.

B. Turn the bottom plate to the right or left in the

desired sawing angle.

You can read this on the protractor. The

maximum sawing angle is 45º.

C. Tighten the socket head screws again.

Connecting and removing the battery

Fig. A + E

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (4) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type.

Using any other batteries could cause

serious injury or damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion.

CDA1053: FPB-1800N, 18V NiMH.

The following charger can be used to

charge these batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH).

CDA1054: FPL-1800N (NiMH only).

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Switching on and off

This machine is equipped with a safety switch.•

Start the machine by pressing the “lock off” •

button (to disengage the switch) and switch on

the machine.

Release the (On/Off) switch to switch the •

machine off.

Speed control

Fig. A

The speed of the saw blade can be controlled with

the rotary knob at the top of the jig saw.

The higher the position, the higher the speed.

The highest position is 6. The ideal sawing speed

will depend on the profile and the tooth of the saw

blade and on the material you want to saw. For

soft materials, select a reasonably high speed and

a coarse tooth. If you want to saw hard materials,

select a lower speed and a fine tooth.

Pendulum setting

Fig. F

For an optimum sawing result you must set the

way in which the teeth of the saw blade

grip the material. You do this by adjusting the

pendulum (8).

Soft material (wood, plastics etc.): set the •

pendulum to level II or III. For a sharp saw cut,

use pendulum level 0 or I.

Medium-hard material (hardwood, aluminium •

etc.): set the pendulum depending on the

application. For thin material use pendulum

level 0, or I if you are working with rasps or

knives.

Hard material (steel etc.): set the pendulum to •

level 0.

Curves: set pendulum to level 0.•

You can adjust the pendulum level while the

appliance is in operation.

Guard

Fig. A

The jig saw is fitted with a guard (10). Make sure

that this guard is always mounted correctly while

the jig saw is in use.

Sawing

Switch on the jig saw.•

Place the bottom plate of the appliance on the •

work piece.

Move slowly towards the previously drawn •

sawing line and press the jig saw forward

slowly. Press the bottom plate firmly against

the work piece. If you do not do this the jig saw

is likely to vibrate and the saw blade will break.

Let the jig saw do the work. Do not press

too hard on the jig saw.

Cutting in

Fig. G

If the starting position of the work piece to be sawn

is not the side, or if no hole has been drilled, you

must cut in. To do this, proceed as follows:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JSM1019 FPJS-1800LK in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm JSM1019 FPJS-1800LK Manual

Product: