Manual Ferm JBM1001 (page 3 of 48) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510133

Zoom out

Zoom in

1/48

Ferm

HYDRAULIC JACK

The numbers in the following text refer to the

picture on page 2

For your own safety and that of others, we

recommend that you read this instruction

manual carefully before using this

machine. Keep this instruction manual

and the documentation provided with the

saw for future reference.

Know your apparatus

Before attempting to operate the apparatus,

familiarise yourself with the controls and make

sure you know how to stop it quickly in an

emergency.

Contents

1. Safety instructions

2. Using the apparatus

3. Service & maintenance

Technical specifications

Fig. 1

Lpa Sound pressure level <70dB(A)

1. Safety instructions

Explanation of the symbols

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Special safety rules

Non-observance of the following instructions can

cause personal injuries and/or damage to the

vehicle.

• Beforejackingupthecar,makesurethejack

is as near to the wheel to be lifted as possible

and as far under the body or any other point of

support as possible.

• Themaximumloadindicatedonthejackmust

neverbeexceeded.

• Thejackmustbeusedasaliftingdeviceonly.

• Alwaysplacethejackonahardandlevel

surface.

• Alwaysprotectthecarfromrollingaway.

Before jack ing up the car, place chocks behind

and in front of the wheels remaining on the

ground, if necessary. Put the car in first gear or

put on the handbrake to further block the car.

• Makesuretoplacethejackinsuchawaythat

your hand is not underneath the car when

jacking it up.

• Makesurethejackisplacedvertical.

• Foryourownsafety,beforeworkingor

crawling underneath the car jack up the car

and support the shafts.

• Beforeusingtheshaftsupportsmakesure

they are in good condition.

• Shouldthepressureinthejackbecometoo

high,excessairwillescapethroughtherelief

valve.Thereliefvalvehasbeensetinthe

factory.

2. Using the apparatus

Assembling the jacking beam

Telescopebothpartsofthejackingbeam,allowing

the flat side to be used when opening and closing

the cock to lower the jack.

Lifting

• Putthecarin‘1’orengagethehandbrake

and block the wheels to prevent the car from

moving.

• Closethecockbymeansofthejackingbeam.

• Instalthescrewjackintherightplace

(indicated by the car manufacturer).

• Insertthejackingbeamintothejackingpoint

and move the jacking beam up and down.

Shaft supports

• Afterjackingupthecartheshaftsupports

should be installed.

• Lowerthecarbyturningthethescrewofthe

release valve anticlockwise, until the car rests

on the supports. Never work under a car which

only rests on the trolley jack.

Lowering

Fig. 1

When you have finished the job, jack up the car

until the jack stands are free. Remove the jack

stands. Using the jacking beam, very slowly and

counterclockwise open the cock referred to under

3. Service & maintenance

Regular maintenance of the hydraulic

jack prevents unnecessary problems.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm JBM1001 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm JBM1001 Manual

Product: