764194

Ferm HDM1038P Manual

6
Zoom out
Zoom in
Previous page
1/108
Next page
6
EN
Exchanging and removing drill bits
Fig. A - B
Before exchanging bits, first remove the
power plug from the wall socket.
Inspect bits regularly during use. Blunt
bits should be re-sharpened or replaced.
Lightly oil the bit shaft before inserting it
into the chuck.
• SDS drills can be inserted by pushing the drill
into the chuck until a click can be heard. If
needed rotate the SDS drill a little to ensure the
keyway in the bit fits the chuck well.
DO NOT slide the locking sleeve (7) to the
rear when inserting bits.
• To remove the SDS drill, slide the locking
sleeve (7) to the rear and remove the SDS drill
while keeping the sleeve (7) in this position.
Setting depth stop
Fig. A
• The depth stop ruler can be added to the side
handle by pushing the dept stop button (9).
• Keep pushing the depth stop button (9) and
insert the depth stop ruler (8) through the hole
on the side handle ring.
• Slide the ruler to the desired depth.
• Loosen the depth stop button (9).
The On/Off switch
Fig. A
• Switch the machine on by pressing the On/Off
switch (2). When releasing the On/Off switch
(2) the machine will turn off.
• The rotation-speed can be continuously
adjusted by pressing the On/Off switch (2)
deeper or less deep.
Lock-on button
Fig. A
• Lock the On/Off switch (2) by pressing the On/
Off switch (2) and then pressing the lock-on
button (4).
• Release the switch-lock by shortly pressing
the On/Off switch (2) again.
Switching the direction of rotation
Fig. A.
• Direction of rotation counter-clockwise: shift
left/right switch (1) to “ ”.
• Direction of rotation clockwise: shift left/right
switch (1) to “ ”.
This function is only available when the machine
is set to “drill mode” (As shown in fig. D function
A & B).
Function selection switch
In order to avoid damage to the machine,
adjusting the function selection switch (5)
shall only be done when machine is not
running. Fig. C
Fig. D
The correct position of the function selection
switch (5) for each function is shown in the
pictures in fig. D. Always make sure the function
switch clicks in the desired position.
A) Drilling (without hammer function): for drilling
in several materials.
B) Hammer Drilling (with hammer function): for
drilling in masonry such as brick, concrete and
similar material.
C) Chisel angle adjustment: for changing the
angle of the chisel. When set under right angle
switch back to position D. before using the
tool.
D) Chipping (chisel function): for chipping and
small demolition jobs.
User tips
Always use the machine with the side handle
firmly anchored in place - you will not only work
with more comfort, you will also work with more
precision.
Caution: drills and chisels can get very
hot.
Drilling and hammer drilling (function A and B)
• For large holes, for instance in very hard
concrete, start using a smaller bit for pilot
drilling first, then drill to nominal size.
• Hold the machine firmly with 2 hands. Be
aware the drill can jam and because of that
machine might suddenly turn (especially when
drilling deep holes).
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm HDM1038P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HDM1038P in the language / languages: All languages as an attachment in your email.

The manual is 16,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info