762272
4
Zoom out
Zoom in
Previous page
1/88
Next page
4
EN
Before connecting the plug to the mains
voltage you have to check if the switch is in
position “0”;
Keep the mains lead always away from the
mouthpiece of the hot air gun;
Keep children and animals away from the
appliance if you are using it.
Immediately switch off the appliance when:
Plug and/or cable are defective or damaged;
The switch is defective;
You smell or see smoke caused by scorched
insulation from the hot air gun.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don’t need any earthed plug
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable
reel always unwind the reel completely.
3. USING THE APPLIANCE
The Hot air gun can be used for:
Plumbing work like tube connections, solder,
bowing tubes;
Removing paint, varnish and lacquer without
firerisk;
Quickly drying of appliances which have
become wet;
Drying surfaces for quick repairing;
Removing self-adhesive labels in a clean way
placing PVC labels;
Blistering after sticking PVC materials can be
smoothed after heating;
Easy removing of vinyl carpeting:
Forming all synthetics with a low temperature
(450 degrees) among which polyethylene and
PVC;
Forming all synthetics with a high temperature
(580 degrees) among which acryl and plexiglass;
Smelting synthetics, among which matters and
foils with PVC layer;
Applying heat shrinking tubes;
Shrinkwrappers;
Thawing tubes and engines;
Repairing finishing layers: enamel of bath and
household appliances;
Applying epoxypowder coverlayers;
Repairing of ski’s, surf-boards and other
sports goods;
Unscrewing too fast fixed screws and
connections.
Operation
Fig. A
You can work manually with this hot air gun or you
can put it in a vertical position.
Check if the mains switch is on position “0”
before you connect the apparatus;
Keep the main lead always away from the hot
air stream and the mouth piece;
Put the mains switch in position ‘I or II’ to let
your hot air gun operate:
“I” = 450 degrees, air flow 300 l/min.
“0” = Off
“II” = 600 degrees, air flow 500 l/min.
When the temperature is excess 600° C, the heats
switches it off automatically, however, the heater
continues to run. When the heater has cooled to
operating temperature, the heater is switched on
again.
Switching off:
Slide the switch to 0.
Tip: If you want to get the best result, test all
appliances on a little part of the workpiece.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm HAM1015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm HAM1015 in the language / languages: All languages as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info