Manual Ferm GRM1013 (page 5 of 16) (English)

632738

Zoom out

Zoom in

1/16

injury. Read the following safety instructions and

also the enclosed safety instructions.

Electrical safety

• Always check if your mains voltage

corresponds with the value on the type plate.

• When replacing old cables or plugs:

• Throw away old cables or plugs immediately

as soon as new ones have replaced these. It is

dangerous to put the plug of a loose cable into

the socket outlet.

• When using extension cables:

• Only use an approved extension cable that is

suitable for the machine’s power. The cores

must have a diameter of at least 1.5 mm

When the extension cable is on a reel, unroll

the cable in its entirety.

• All electrical connections e.g. extension

cable, must be of an approved waterproof

type for outdoor use and marked accordingly.

Extension cables must be threecore, one of

which is EARTH.

Immediately switch off the machine when:

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

Specific safety rules

The USE and MAINTENANCE manual constitutes

an essential part of the cleaner equipment and

should be kept in a safe place for future reference.

If you sell the cleaner, the manual should be

handed on to the new owner.

• Before starting the cleaner, make sure that

it is receiving water correctly. Operating the

cleaner without water could damage the seals.

• Do not disconnect the plug by pulling on the

electrical cable.

• If you are too far from the object you wish

to clean, do not move the cleaner nearer by

pulling on the high pressure hose; use the

handle provided.

• In versions not equipped with TSS device,

do not operate the cleaner for more than 1-2

minutes with the gun closed as this could

damage the seals.

• Protect the cleaner from freezing during the

winter.

• Do not obstruct the ventilation grilles during

operation.

• The cross-section of any extension cables

used must be proportional to their length, i.e.

the longer the extension cable, the greater the

cross-section; cables with a protection level of

“IPX5” must be used.

• Position the cleaner AS NEAR POSSIBLE to

the water supply.

• The packaging is easily recyclable, and must be

disposed of in compliance with the regulations

in force in the country of installation.

• Use the cleaner only with accessories

and replacement parts authorized by the

manufacturer. The use of original accessories

and replacement parts will ensure safe,

trouble-free operation.

• The cleaner must be used standing on a

secure, stable surface.

• Avoid unintentional firing of the trigger. Do not

carry the lance/ trigger assembly with your

hand over the trigger. Always use the trigger

lock mechanism.

• Ensure that the safety lock on the trigger

is used, when you have stopped using

the pressure washer to prevent accidental

operation. (fig 5)

• Read all the instructions before using the

machine.

• Machines shall not be used by children.

Children should be supervised to ensure

that they do not play with the machine. This

machine is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge

• The electrical supply connection shall be made

by a qualified person and comply with IEC

60364-1. The electric supply to this machine

should include either a residual current device

that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a

device that will prove the earth circuit.

• The machine is intended to be used at

a temperature above o degree. (Only for

machine with power cord of H05VV-F).

• The operating method to be followed in the

event of accident (e.g. contact with detergents:

rinse with an abundance of clean water) or

breakdown to prevent unsafe situations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm GRM1013 in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm GRM1013 Manual

Product: