632735
6
Zoom out
Zoom in
Previous page
1/30
Next page
3. SAMLING
TILSLUTNING AF SLANGE OG PISTOL MED
AFBRYDER
Fig. 1 og 2
Før slanger og pistol/lanse tilsluttes, skal man
kontrollere, at der ikke er snavs o.l. i
forbindelsespunkterne.
Skru højtryksslangen (7) på maskinen og stram den
godt til med hånden.
Sæt lansen med strålespids (5) sammen med pistolen
(6) ved at trykke bajonetfatningen ind og dreje (fig. 2).
Sørg for, at de to dele er samlet rigtigt og sidder godt
fast. Kontroller, at der ikke er knæk på slangen.
VANDFORSYNING
Sørg for korrekt vandforsyning til højtryksrenseren.
Kontroller, at alle forbindelser er strammet til, og at
der ikke er utætheder i slangen
Vandhanen skal åbnes helt (højtryksrenseren må
ikke startes endnu).
Nu trykkes pistolafbryderen ind (låsemekanismen
skal først slippes), så vand kan strømme gennem
maskinen og presse eventuel luft ud.
Der skal bruges koldt vand til højtryksrenseren!
Tænd for højtryksrenseren, når al luft er presset ud,
og der kun kommer vand ud af spidsen.
EL-LEDNINGER
Kontroller ledninger for beskadigelser, før strømmen
tilsluttes. Sæt stikket i stikkontakten og start maskinen
på hovedafbryderen (3).
4. BRUG
Der må kun bruges rent vand; hvis der bruges
ufiltreret vand eller ætsende kemikalier, kan det
beskadige højtryksrenseren.
Sæt motorafbryderen i position ”0”.
Kontroller, at forsyningsspændingen og -frekvensen
(Volt/Hz) stemmer overens med specifikationerne
på mærkepladen.
Hvis strømforsyningen er i orden, kan stikket sættes i
stikkontakten.
Elinstallationen skal være udført af en elinstallatør.
Det anbefales, at der ved stikkontakten er installeret
en fejlstrømsafbryder (RCD) på højst 30 mA.
Maskinen kan forårsage forstyrrelse i
strømforsyningen i forbindelse med start.
Hvis motoren stopper og ikke vil starte igen, ventes der
2-3 minutter, før der prøves igen. TERMOSIKRINGEN
ER UDLØST
JUSTERING AF STRÅLESPIDSEN
Fig. 3
Vandet kan sprøjtes ud af strålespidsen i en tæt stråle
eller i vifteform. Slå trykket til og juster derefter
strålespidsen.
Filteret i vandindløbet skal kontrolleres jævnligt for
tilstopning, så vandet kan strømme uhindret. (fig. 4)
BRUG AF BEHOLDEREN TIL
RENGØRINGSMIDDEL
Tanken til rengøringsmiddel fyldes med flydende
rengøringsmiddel. Når pistolafbryderen nu trykkes ind,
mens maskinen er startet, sprøjtes der
rengøringsmiddel ud sammen med vand.
ANBEFALET RENGØRINGSPROCEDURE
Snavs blødgøres ved at sprøjte rengøringsmiddel i
vifteform på overfladen. På lodrette overflader skal man
arbejde nedefra og op. Lad rengøringsmidlet indvirke i 1
til 2 minutter, men lad det ikke tørre helt. Brug nu
højtryksstråle, idet strålespidsen holdes mindst 30 cm
fra overfladen, og der arbejdes nedefra og opad. Lad ikke
skyllevandet løbe over overflader, der ikke er blevet
behandlet med rengøringsmiddel.
SÅDAN AFBRYDES HØJTRYKSRENSEREN
Højtryksslangen må ikke skrues af maskinen,
mens systemet stadig er under tryk. Gør sådan:
1. Sluk for højtryksrenseren på hovedafbryderen på
maskinen.
2. Tag stikket ud af stikkontakten.
3. Luk for vandet på vandhanen.
4. Tryk på afbryderen på pistolen for at tage trykket af.
5. Tag vandslangen af maskinen
6. Tør maskinens overflader af med en fugtig klud.
7. Sæt låsemekanismen i indgreb.
FEJLFINDING
1. Når der tændes, starter maskinen ikke
Stik ikke sat rigtigt i eller stikkontakt defekt
- Check stik, stikkontakt og sikring
Netspændingen er for lav til at starte maskinen
- Check, at netspænding er korrekt
Pumpen sidder fast
- Se instrukser for brug, efter maskinen ikke har været
brugt i længere tid
Termosikring udløst
- Sluk maskinen og lad motoren afkøle.
- Lad lansen være åben og vand strømme ud
2. Skiftende tryk
Pumpe suger luft
- Check, at slanger og forbindelser er lufttætte
Ventiler snavsede, slidte eller tilstoppede
- Pumpetætninger slidte
- Rens og sæt i igen eller kontakt forhandler
3. Pumpen lækker vand
Tætninger slidt op
- Check og udskift eller kontakt forhandler
4.Motoren stopper pludseligt
Termosikring udløst på grund af overophedning
Check at netspændingen stemmer overens med
specifikationerne.
- En for tynd og for lang forlængerledning kan
forårsage spændingsfald, så motoren overophedes.
Lad motoren afkøle.
55 Ferm
procedure in this manual, turn the pressure washer ON
and just squeeze the trigger for activation.
ADJUSTING THE NOZZLE
Fig. 3
Water may be sprayed out of the nozzle either linearly
or in a fan shape. Turn on the pressure first, and then
adjust the nozzle.
The water inlet filter must be inspected regularly, so as
to avoid blockage and restriction of the water supply to
the pump. (fig 4)
USING THE DETERGENT BOTTLE
The detergent nozzle and tank attaches to the end of the
trigger assembly in the same way as the lance does. Fill
the detergent tank with liquid detergent. When the
trigger is now pressed with the machine running,
detergent will spray out with the water.
RECOMMENDED CLEANING PROCEDURE
Dissolve dirt by applying detergent with the fan jet to the
dry surface. On vertical surfaces, work from the bottom
upwards. Leave the detergent to act for 1 to 2 minutes,
but do not allow to dry out. Apply the high pressure jet,
keeping the nozzle at least 30 cm (10 in.) from the
surface, working from the bottom upwards. Avoid
allowing the rinsing water to run on to unwashed
surfaces.
Shutting down the pressure washer
Never disconnect the high- pressure hose from the
machine while the system is still pressurized.
Follow the correct procedure:
1. Turn off the pressure washer by using the switch on
the machine.
2. Unplug the unit from the power source.
3. Turn off the water supply at the tap.
4. Press the trigger of the gun to depressurize the
system.
5. Disconnect the supply hose to the machine
6. Wipe all surfaces of the unit with a damp clean cloth.
7. Engage the safety lock.
TROUBLESHOOTING
1. When switched on, the machine will not start
working.
Plug is not well connected or electric socket is faulty
- Check plug, socket and fuse.
The mains voltage is lower than the minimum
requirement for start up
- Check that the mains voltage is adequate.
The pump is stuck
-- Refer to after storage instructions
-- Switch off the unit and let the motor cool.
Thermal safety has tripped
- Leave the lance open with water coming through.
2. Fluctuating pressure
Pump sucking air
- Check that hoses and connections are airtight.
Valves dirty, worn out or stuck.Pump seals worn
- Clean and replace or refer to dealer.
3. Water leaking from the pump
Seals worn out
- Check and replace, or refer to dealer
4. The motor stops suddenly
Thermal safety switch has tripped due to
overheating.
- Check that the mains voltage corresponds to
specifications. An extension cable, which is too thin,
and - tool long can cause a voltage drop
and cause the motor to overheat. Leave to cool down.
Use heavy duty extension cables.
5. The pump does not reach the necessary
pressure.
Water inlet, filter is clogged
- Clean the water inlet filter
Pump sucking air from connections or hoses
- Check that all supply connections are tight
Suction/ delivery valves are clogged or worn out.
- Check that the water feeding hose is not leaking.
Unloader valve is stuck
- Clear or respire valves
Lance nozzle incorrect or worn out
- Loosen and re-tighten regulation screw.
- Check and/ or replace.
6 Ferm
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm GRM1006 - FHPW 160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm GRM1006 - FHPW 160 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info