510094
3
Zoom out
Zoom in
Previous page
1/68
Next page
EN
3
Ferm
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
Only use an approved extension cable suitable for
the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.

Always observe the safety instructions
and applicable regulations.
This glue gun (kit) has been especially designed
for glueing products such as wood, plastic, foam,
rubber, fabric, cardboard, tiles, ceramics, etc.
Quickly setting, the glue is perfect for repairing
carpets, bookbinding, fixing soles, etc. The glue is
waterproof and resistant to the action of many
liquids. The glue gun is quick, environmentally-
friendly, energy-saving and together with the glue
facilitates and quickens any job.
Due operating the glow gun
• The normal setting time of the hot glue is 30
seconds. After 30 seconds the glue starts to
set. Having applied the glue on the relevant
surfaces, wait 15 - 20 seconds before joining
them.
• After about 1 minute the joint has reached
90% of its adhesive strength.
• The setting time can be extended to 50 to 60
seconds by applying the glue in thick drops or
shortened by applying the glue in short, fine
lines.
• Joining large surfaces is difficult, as the glue
tends to set before the entire surface has been
covered with glue.
• Preheating the surfaces to be joined
guarantees a strong joint. Sun rays have the
same impact.
• The glue melts from a temperature of approx.
140°C and must never be used on material
that is sensitive to heat.
• The glue gun can be used to replace nails,
paper tape, liquid glue, but not for heavy-duty
jobs.
• The electric glue gun features accurate
temperature control. It is fitted with a special
design feed system that ensures no glue is left
behind inside the mechanism.
• The glue gun requires Ø 11.2 mm glue
cartridges.
• The glue gun comes standard with a bracket
that enables you to put the gun safely on the
table when it is not used.
Operation
• Plug in the tool.
• Insert a glue cartridge into the gun, two when
using it for the first time.
• Wait 5 minutes for the glue to heat.
• Squeeze the trigger to release the glue.
• Replace the glue cartridge as soon as you
notice little if any glue is released from the
gun.
• Disconnect the tool if you do not intend to use
it for some time.
Replacing the nozzle
• Loosen the orange nozzle.
• Fit the nozzle on the glue gun.
Before removing the nozzle, allow the
glue gun to cool down completely to
avoid injuries. Always disconnect the
tool.

Make sure that the machine is not live
when carrying out maintenance work on
the motor.
This machine has been designed to operate over
a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Always disconnect the tool before
cleaning and maintenance work. Never
use inflammable liquids to clean the tool.
Use a brush to clean the glue gun.
• Keep the nozzle clean. Check before every
use there is no glue left on the nozzle.
• Remove any glue left inside the nozzle with a
pin.

Should the machine fail to function correctly, a
number of possible causes and the appropriate
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm GGM1002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm GGM1002 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info