79014
4
Zoom out
Zoom in
Previous page
1/24
Next page

     .

     
,    
     
.
     
     
  .
  
      
,     
,     
   . ,
     
    .

     
    ,
   .
    ,  
       
 
EN60745-1, EN60745-2-4,
EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
   
98/37/EEC
73/23/EEC
89/336/EEC
  01-06-2004
ZWOLLE NL
W. Kamphof
 

      
   ,  
    
   
.
CE
ı
  
(
GR
)
Ferm 45
REPLACING WORN SANDING PAPER
Fig. 3
Before assembly sanding paper always remove
the plug from the mains.
1. The sandpaper (7) is fixed by Velcro fast-
ener to facilitate the replacement.
Simply pull off the sanding paper
Press the new one in the centre of the sanding
sole (8)
Coarse sand-paper (grain 50) removes in general the
bigger part of the material and fine sand-paper (grain
120) is used for the finishing.
2. The sanding machine is provided with a
rectangle sanding sole. By tightening the
sandpaper it does not wear out so fast, so it
will wear well longer.
Open the back paper clamp (4) by pulling the
handle (5) up.
•Install the sandpaper under the clamp. Put the
paper in the middle of the sanding sole and look
after the perforations in the paper. They have to
correspond with those on the sanding sole, so
that the dust can be exhausted.
Push the handle back into its original position.
Repeat the operation to fix the sand-paper on the
front side.
Fix the sandpaper as tight as possible.
REPLACING THE SANDING SOLE
The sole has to be replaced when the Velcro has
been worn out.
Before replacing the sanding sole disconnect the
sander from the mains.
Remove the sandpaper of the sole.
Remove the screws which the sole is fixed to the
sander.
Remove the sole.
•Install the new sole on the sander.
Tighten the screws well.
4. USE
OPERATION
Hold the sander on the handle (2), so as to gain
the best possible control over your sanding ope-
rations.
The ventilating apertures (6) on the housing must
remain clear to ensure optimum cooling of the
motor.
Push the on/off switch (1) to start the machine.
Move the sander over the surface of your work-
piece.
Push the on/off switch to stop the machine.
Prevent pushing too much on the machine
during sanding. Excessive sanding pressure does
not lead to increased sanding capacity, but increases wear
of the machine and the sandpaper .
USER TIPS
Apply long uniform movements to your sander to
obtain the best possible results.
The surface quality after sanding is determined by
the selected grain.
5. SERVICE & MAINTENANCE
TROUBLESHOOTING
1. The electromotor gets hot:
Clean the ventilating apertures
2. The dust is not extracted:
The dust bag is full / empty the dust bag
3. The abrasive paper is filled with adhesive/-
paint or a similar material:
Paint or adhesive is not really dry.
Some paints stick more to the abrasive paper
than others / clean the abrasive paper at regular
intervals
CLEANING
Clean the housing regularly with a soft cloth, prefera-
bly every time it is used. Keep the ventilating apertu-
res free from dust and dirt.
Remove stubborn dirt with a soft rag moistened in
soapy water. Do not use any solvents such as petrol,
alcohol, ammonia, etc. as such substances can damage
the plastic parts.
LUBRICATION
The appliance does not need any extra lubrication.
FAULTS
If a fault arises through wear in an element, please
contact the service address shown on the warranty
card.
A drawing of the spare parts that may be obtained is
included at the end of these operating instructions.
ENVIRONMENT
To prevent damage during transport, the appliance is
delivered in a solid packaging which consists largely of
reusable material. Therefore please make use of
options for recycling the packaging.
WARRANTY
Read the terms of warranty on the separate warranty
card which is enclosed.
4 Ferm
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FPS 180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FPS 180 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info