383488
8
Zoom out
Zoom in
Previous page
1/56
Next page
GB
8 Ferm
Pull out and tighten the cut depth clamping •
knob (16) once the correct depth is set. The
cut depth clamping knob needs to be pulled
out in order to function. Make sure it is
securely tightened before using the machine.
Exchanging or cleaning the saw blade
Fig. A + E + F
Press the spindle lock button (14) to prevent •
the spindle from rotating.
Loosen the bolt (3) in the centre of the saw •
blade, using the wrench key (20).
Release the spindle lock button (14).•
Turn the safety guard (2) to the rear and hold it •
there with the aid of the guard knob (1).
Remove the retaining ring (4) and the saw •
blade. Clean the blade or replace it with a new
one. Make sure the arrow on the saw blade,
indicating the direction of rotation,
corresponds with the direction arrow on the
upper guard.
Place the saw blade back on the shaft.•
Release the guard knob the allow the safety •
guard to return over the saw blade.
Press the spindle lock. Refit the retaining ring •
and firmly tighten the bolt.
Connecting and removing the battery
Fig. G
Insert the battery into the base of the •
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking button (17) before removing •
the battery, and disengage the battery from
the base of the appliance.
Only use batteries of the following type.
Using any other batteries could cause
serious injury or damage the tool.
CDA1051: FPB-1800L, 18V Lithium-Ion.
CDA1053: FPB-1800N, 18V NiMH.
The following charger can be used to charge these
batteries.
CDA1052: FPL-1800 (Lithium-Ion and NiMH).
CDA1054: FPL-1800N (NiMH only).
4. OPERATION
Wear ear and eye protection.
Switching on and off
This machine is equipped with a safety switch.•
Start the machine by pressing the “lock off” •
button (to disengage the switch) and switch on
the machine.
Release the (On/Off) switch to switch the •
machine off.
Operation
Hold the work using clamps or a vice to have •
both hands free to operate the saw.
Switch on the saw and place the sole plate on •
the workpiece.
Slowly move the saw towards towards the •
previously drawn cutting line and slowly press
the tool forward.
Firmly press the soleplate on the workpiece •
otherwise the circular saw may start to vibrate,
causing the blade to break more easily.
Let the saw do the job. Do not put undue
pressure on the circular saw. If the saw
blade jams in the workpiece, the
machine will automatically switch off.
Laser beamer
Laser beamer in use
The leading beam of the laser beamer makes
sawing in straight lines much easier:
a) along a drawn line, or
b) by aligning it to a fixed point marked on the
workpiece. Press the laser on/off button (8) to
switch the laser on or off.
Adjusting the laser beam
Transport handling and heavy use can affect •
the precision of the laser beam.
The laser beam itself can be easily adjusted.•
Hold the blade of the circular saw against a •
straightedge or perfectly straight plank.
Switch the laser on. •
Check whether the laser beam runs parallel •
along the edge of the straightedge or plank.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fpcs 1800 csm1028 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fpcs 1800 csm1028 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info