Manual Ferm FPCD 1800 LK (page 8 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

78741

Zoom out

Zoom in

1/64

8 Ferm

11-15: For driving screws into soft and medium-

density materials

16-20: For driving screws into hardwood

21-25: For driving large screws

Drill icon: For drilling

Hammer icon: For impact drilling

If material is particularly soft or porous,

set the torque clutch at a lower setting to

avoid overdriving the screw.

Adjusting the speed

Fig. 1

The appliance has two drill speeds.

For slow drilling or for driving or removing •

screws, set the speed selection switch (3) to

‘1’.

For fast drilling set the speed selection switch •

to ‘2’.

Never switch over when the motor is

running!

Driving and removing screws

Fig. 1

Set the direction reversing switch (8) to •

position ‘’ in order to drive screws.

Set the direction reversing switch (8) to •

position ‘’ in order to remove screws.

Ensure that the direction reversing

switch (8) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. 1

Depress the on/off switch (9). It regulates the •

speed of the appliance by transmitting power

to the switch.

Release the on/off switch (9) to halt the drill •

chuck immediately, it will no longer run on.

Move the direction reversing switch (8) to the •

centre in order to lock the appliance in its

disabled state.

The drill will turn at its slowest speed when the

switch is depressed lightly. The drill will turn at its

fastest speed when the trigger is fully depressed.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Spirit level

Fig. 8

The drill is equipped with a dual reading horizontal/

vertical level to assist in keeping the drill “level”

while drilling horizontal and vertical holes. The

horizontal level (21) is located in the top of the drill

housing. The vertical level (22) is located on the

rear of the drill housing.

To maintain a level drilling position, hold the drill

where the level bubble is centred in the level

indicator circle.

LCD display

Fig. 9

This combi drill is equipped with an LCD display

(4) on top of the drill housing

To turn the display on, press the display button •

(27) once. To turn the display off, press the

display button again.

The light icon (25) will become visible when •

the LED work lights are turned on.

The clock (28) and minutes (24) remaining •

icons indicate the number of minutes of

running time that are available before the

battery requires recharging (Lithium Ion

battery only)

The battery icon (23) indicates the amount of •

charge remaining in the battery. Each charge

bar displayed indicates approximately 10%

charge remaining in the battery. A total of 10

charge bars indicates a fully charged battery.

Dual LED work lights

Fig. 1 + 9

Dual LED lights (12) are located behind the torque

ring. The LED light switch button (26) is located

below the LCD display on top of the drill.

To turn the LED lights on, press the LED light •

switch once.

To turn the LED lights off, press the LED light •

switch again.

The display must be turned on first, in order for the

LED lights to work.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FPCD 1800 LK in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FPCD 1800 LK Manual

Product: