79013
7
Zoom out
Zoom in
Previous page
1/42
Next page
Ferm 07
Abrasive cloth with Velcro fastener
Foam disks with Velcro fastener
Remove used disks from the Velcro fastener.
Put the new disk on and press slightly.
Polishing hoods
First reverse the polishing hood and place it on the Velcro fastener.
Then pull the elastic edge tightly over the disk.
4. USE
See Fig. 1.
Only use clean sanding and polishing materials.
For preliminary sanding, use coarse sanding disks and medium to fine sanding disks for
finishing.
The delivery kit of the device contains foam disks for apply the polish (low speed).
The polishing hoods made of textile fleece (high speed) are suitable for the finished polishing.
The ON/OFF switch
To turn the device on, press the ON/OFF switch (1).
To turn the device off, press the ON/OFF switch again (1).
Setting the speed
The speed can be set (from slow to fast) using the continuous speed adjustment wheel (2).
User tips
Always hold the device with 2 hands. You will not only be safer, but your work will be less tiring
and more effective.
Sanding
With the abrasive cloth disks provided, you can also use the device for sanding.
Polishing
Attach the foam disks.
Spread the polish evenly over the entire surface of the disk.
Hold the polishing disk against the surface to be polished and switch the device on.
Move the device evenly across the surface to be polished. Do not exert any pressure.
Always switch the device off before you remove it from the polishing surface.
Spread more polish on the surface of the disk until the entire surface that is to be polished
has been treated.
Remove the foam disk from the polishing disk and attach the fine fleece polishing hood.
Buff to a brilliant finish using the same method and sequence that you used when you
applied the polish.
GB
D
NL
F
E
P
I
S
FIN
N
DK
78 Ferm
Indstilling af omdrejningstallet
Omdrejningstallet kan indstilles trinløst mellem langsomt og hurtigt ved hjælp af drejeknappen
for omdrejningstallet (2).
Tip til brugeren
Hold altid maskinen med to hænder – på den måde arbejder du mere sikkert, mere bekvemt og
mere effektivt.
Slibning
Ved hjælp af de medfølgende skiver af smergellærred kan du også bruge maskinen til slibning.
Polering
Anbring skumplastskiverne.
Fordel poleremidlet regelmæssigt over hele skivens overflade.
Hold poleretallerkenen mod den flade, der skal poleres, og tænd maskinen.
Bevæg maskinen regelmæssigt hen over den flade, der skal poleres. Undgå at lægge tryk
på. Sluk altid maskinen, inden du fjerner den fra den flade, der poleres.
Fordel igen poleremiddel på skivens overflade, indtil hele den flade, der skal poleres, er
behandlet.
Tag skumplastskiverne af poleretallerkenen, og anbring den fine polerehætte af
fleecetekstilmateriale.
Poler til højglans på samme måde og i samme rækkefølge, som du har anbragt
poleremidlet.
Tip til optimale resultater ved polering af biler
Vask bilen mindst hver 4. uge. Vask bilen ovenfra og ned.
Poler bilen to eller tre gange om året.
Poler først de store flader (f.eks. taget og motorhjelmen) og derefter de mindre (f.eks.
dørene). Poler steder, der er svære at komme til, med håndkraft.
Anvend altid rene polerehætter.
Poler ikke i solskin på varme lakflader.
Tag hensyn til poleremiddelproducentens anvisninger:
5. SERVICE OG VEDLIGEHOLDELSE
Vedligeholdelse
Apparaterne er konstrueret til langtidsbrug med minimal vedligeholdelse. Apparatet vil fungere
tilfredsstillende i lang tid under forudsætning af, at det plejes korrekt og rengøres
regelmæssigt.
Rengøring – tag først lysnetstikket ud af fra stikkontakten
Rengør apparathuset regelmæssigt med en blød klud og helst hver gang apparatet har været
brugt. Hold udluftningshullerne fri for støv og snavs. Hvis snavset ikke kan fjernes på denne
måde, anvendes en blød klud, der er fugtet med sæbevand. Anvend aldrig opløsningsmidler
som f.eks. benzin, alkohol osv. Disse opløsningsmidler kan beskadige kunststofdelene.
UK
D
NL
F
E
P
I
S
FIN
N
DK
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FMMS 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FMMS 120 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info