382947

Ferm fks 180 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
BEFORE USING THE SAW
Ensure the saw is unplugged from mains before
making adjustments, mounting accesories or chan-
ging blades.
CHANGING/FITTING SAW BLADES
Refer to illustration below
- Depress the spindle lock lever (6) and keep it pressed,
then use the 13mm box spanner (2) provided to turn
the blade-retaining bolt anticlockwise.
- Remove the bolt, washer and blade if fitted. Make sure
the flange is present on the shaft and is the right way up.
- Open the blade guard with lever (1) and replace or fit
the saw blade with the teeth facing the same way as the
riving knife (4) - the teeth face towards the front of saw.
- Fit the washer and bolt (clockwise) hand tight.
- Depress the spindle lock lever and keeping it pressed,
tighten the bolt securely with the box spanner.
- Check that the blade guard is free to revolve and that
the blade does not touch any part of the casing or guard.
- After fitting a new blade it may be necessary to adjust
the riving knife.
ADJUSTING THE RIVING KNIFE
Refer to illustration below.
- Use a suitable screwdriver (not supplied) to loosen
both screws (2)
- Rotate Blade guard with lever (1) and keep open while
adjusting the riving knife. Refer to the illustration for
minimum and maximum distances.
- Tighten both screws securely.
- Check that the riving knife is in the correct position and
is in line with the blade.
- Release the blade guard.
MOUNTING THE PARALLEL GUIDE
Referring to the illustration below.
- Loosen thumbscrew (1)
- Slide the parallel guide (2) into slots with the fence
facing downwards.
- Set guide to the required position
- Tighten thumbscrew.
ADJUSTING THE CUTTING ANGLE
Referring to the illustration below.
- Loosen (anticlockwise) the thumbscrew (1) on the
angle quadrant and the locking lever (rotate anti-
clockwise) located at the rear of blade.
- Set the shoe to the desired angle 0-45 degrees.
- The cutting angle is indicated by the pointer (3)
- Securely tighten the thumbscrew and the locking lever.
ADJUSTING THE DEPTH OF CUT
Referring to the illustration below.
- Loosen locking lever (1) anticlockwise.
- Move the shoe (2) downwards to required depth
marked on quadrant (3)
- Securely tighten locking lever clockwise.
1 2
3
1
3
2
45
30
0
1
2
80
A=45
B=90
max 5 mm
max 5 mm
3
2
1
1
4 3 5
2
4 Ferm Ferm 9
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fks 180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 180 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm fks 180

Ferm fks 180 User Manual - German, Dutch, French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info