Manual Ferm fks 165l2 (page 4 of 30) (English, German, Dutch, Danish, French, Italian, Norwegian)

382449

Zoom out

Zoom in

1/30

Dispose of old cables or plugs immediately after

replacing them with new ones. It is dangerous to connect

the plug of a loose cable to a socket.

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

. When using a cable reel always unwind

the reel completely.

Danger

a) Keep hands away from cutting area and the blade.

Keep your second hand on auxiliary handle, or

motor housing. If both hands are holding the saw,

they cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the

workpiece.

c) Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

d) Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform.

It is important to support the work properly to

minimize body exposure, blade binding, or loss of

control.

e) Hold power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with

a "live" wire will also make exposed metal parts of the

power tool "live" and shock the operator.

f) When ripping always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces

the chance of blade binding.

g) Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades that

do not match the mounting hardware of the saw will

run eccentrically, causing loss of control.

h) Never use damaged or incorrect blade washers or

bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance

and safety of operation.

Causes and operator prevention of kickback

• Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to

lift up and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into the

top surface of the wood causing the blade to climb

out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by

the operator, if proper precautions are taken.

b) When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the

blade is in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause of

blade binding.

c) When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are not

engaged into the material. If saw blade is binding, it

may walk up or kickback from the workpiece as the

saw is restarted.

d) Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must

be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding

and kickback.

g) Use extra caution when making a "plunge cut" into

existing walls or other blind areas. The protruding

blade may cut objects that can cause kickback.

Safety instructions lower guard

a) Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent.

Raise the lower guard with the retracting handle and

make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts." Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower

guard should operate automatically.

d) Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An

unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after

switch is released.

BEFORE USING THE CIRCULAR SAW:

• Check the following points:

• Does the voltage of the motor correspond with the

mains voltage (appliances for a mains voltage of 230V.

• Are the mains lead and the mains plug in a good

condition: solid, without any loose ends or damage.

• Is the saw blade missing any teeth or showing

any cracks, it so must be replaced immediately.

• Make sure the blade is secure.

4 Ferm

Vi erklærer at under almindeligt ansvar, at dette

FKS-165L2

er i overenstemmelse med følgende

normer eller normative dokumenter

EN60745-1, EN60745-2-5,

EN55014-1, EN-55014-2,

EN61000-3-2, EN61000-3-3,

EN60950, EN60825-1,

i henhold til bestemmelserne i direktiverne:

98/37/EC, 89/336/EEC,

2002/95/EC, 2002/96/EC, 2006/95/EC

01-08-2007

ZWOLLE NL

J.A. Bakker - van Ingen J. Lodewijk

CEO Ferm BV

Quality Manager Ferm Global

Det er vores hensigt til stadighed at forbedre vores

produkter, og vi forbeholder os derfor til enhver tid

retten til at ændre produktspecifikationerne uden

forudgående varsel.

Ferm BV •

Lingenstraat 6 • 8028 PM Zwolle

Holland

KONFORMITETSERKLÆRING

(

)

Ferm 57

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fks 165l2 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 1,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fks 165l2 Manual

Product: