Ferm 05
When operating the machine
• Check if the switch is placed in the ‘OFF’-
position before you connect the machine to
mains.
• Keep the mains cable away from moving
parts of the machine.
• First switch off the machine before you move
the machine downwards along your body.
• Never cover the ventilation slots.
Immediately switch off the machine in case of:
• Excessive sparking of the brushes and
verticiliosis in the collector.
• Malfunction of the mainsplug, -socket or
damaged cables.
• Broken switch.
• Smoke or smell caused by scorched
insulation.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine - Double insulation -
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. BEFORE OPERATING THE
MACHINE
Use only sharp drills of the following types
Fig.B
Concrete/masonry Hard metal
Metal HSS
Wood HSS
Mounting accessoires
Fig.C
Prior to mounting an accessory always
unplug the tool.
Placing and removing bits
In addition to bits the machine can also hold
screw bits with a hexagonal shaft. The drill head
is equipped with a lock function. To tighten or
slacken the drill head, the lock has to be
unlocked first. This is done as follows:
• Hold the drill head (A) and slide the ring (B) in
the direction of the drilling machine. The ring
will jump and the lock is now unlocked.
• Place the shaft of the bit in the nesting place
of the drill chuck. Tighten the bit by holding
ring B and turning the drill head (A).
• Once the bit has been tightened in, slide ring
B in the direction of the drill head, which will
activate the lock. This will stop the drill head
from loosening due to vibration during use.
• Slide the sidegrip over the drillhead.
• Slide the measuring rod in the sidegrip and
tighten the grip by turning the sidegrip.
• Tighten the workpiece to a workbench by
using a clamp.
• When all preparations are done the machine
can be connected to mains. First check if the
switch is in the ‘OFF’-position and if the
rotationswitch is in the RIGHT-position.
4. OPERATION
The on/off switch
Fig.D
Switch the machine on by pressing the
triggerswitch (A). When you release the
triggerswitch (A) the machine will turn off.
GB
40 Ferm
Rengøring
Rengør regelmæssigt maskinkappen med en
blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug
en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual
finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres
maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug
derfor emballagen.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal
afleveres på en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for
garantibetingelserne.
DK
