382948
8
Zoom out
Zoom in
Previous page
1/60
Next page
Ferm 113
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til
at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger kunststofdelene.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er
så vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres
på en genbrugsplads.
Garanti
Se venligst garantibetingelserne på garantikortet, som er vedlagt separat.
Redskabet Strømtilførslen
er blevet afbrudt.
Savklingen er skæv eller
døv.
Savklingen er over
ophedet eller skæv.
Kullene er slidte.
Kontroller om der er
defekter i forbindelsen til
strømforsyningen.
Lever redskabet ind til
Deres forhandler til
eftersyn eller reparation.
Udskift savklingen.
Udskift savklingen.
Lever redskabet ind hos.
Afbryderen er beskadiget.
Kontakt venligst
serviceadressen på
garantibeviset.
Arbejdsemnet begynder at
vibrere kraftigt under
savningen.
Redskaber kører
larmende og/eller meget
ujævnt.
Kontakt venligst
serviceadressen på
garantibeviset.
DK
08
Ferm
3. ASSEMBLY INSTRUCTIONS
Selecting the saw blade
The jigsaw is supplied with 3 saw blades, each with different teeth. the profile and the
teeth vary according to the material that you want to saw. A fine tooth will give you a
smooth and precise saw cut.
Use a narrow profile if you want to saw curves or if you are going to saw figures.
The maximum saw capacity in wood is 70 mm with the enclosed saw blades. With special
saw blades, this machine can saw work pieces till 110 mm. To select the right saw,
proceed as follows:
First of all try a saw blade with coarse teeth.
If you don't get a smooth and precise saw cut, try a saw blade with a finer tooth.
For plastic, aluminium and steel always use a saw blade with a very fine tooth.
In general you will work faster but less precisely with a coarse tooth than with a fine tooth.
For an optimum result always make sure the saw blade is sharp.
The jigsaw is suitable for all commercially available saw blades).
Saw blade
Type of workpiece
Coarse Wood
Medium Wood
Fine Plastic, aluminium, steel
Very fine Cutting curves (wood)
Assembling saw blade
Fig. 2a + 2b
Before assembling the saw blade check that the mains plug has been
removed from the socket.
Replacing/inserting the saw blade:
Pull the lever (7) upwards
Insert the saw blade (teeth in cutting direction) into the stroke rod until it latches.
While inserting the saw blade, pay attention that the back of the saw blade is
positioned in the groove of the guide roller.
Release the lever; the saw blade (10) is locked.
Ejecting the saw blade:
To eject the saw blade pull the lever upwards and at the same time remove the saw
blade out of the machine.
Adjusting the bottom plate
Fig. 3a + 3b
Adjust the angle of the bottom plate (6) as follows:
A. Loosen the socket head screws (12) with the
Allen key supplied.
B. Pull the bottom plate back slightly to unlock it.
GB
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fjs 750 l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fjs 750 l in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 26,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info