INSTALLATION
Warning: Before start-up please read carefully the
instructions.
1. Turn the starting switch into the “0” position.
Connect the high pressure hose to the delivery pipe
OUTLET. Connect the water hose to the INLET.
The presence of red dust in the connections is
normal and does not interfere with the use and
functioning of the machine.
2. Always use the filter supplied. Sand, limestone and
furrings damage the pump valves. Priming soiled
water invalidates the warranty !
3. Open the water tap completely. The limit of the
incoming water temperature has to be 40°C.
4. Connect the plug to the socket. Press the gun lever
so that air and possible pressure residues come out
from the pipes.
5 Keeping the gun lever pressed, switch on the device
by setting the switch to "I".
6. Lance assembly. USE ALWAYS THE LANCE
EXTENSION.
7. At the end of work: a) switch off the cleaner; b)
disconnect the water mains; c) discharge the water
inside the pump and high pressure pipe, leaving the
gun open for a few seconds. This reduces the risk of
scale formation and will facilitate the new electro-
pump starting.
USAGE
8. High pressure nozzle adjustment.
9. Gun safety device.
10. Use of detergent spray attachment. Use only
biodegradable soap.
12. TURBO NOZZLE Nozzle and rotating jet to
increase the washing effect (the turbo lance is not
adjustable).
Model with nozzle Vortex only.
13. WARNING!
Before start up always operate the machine
without the lance. USE ALWAYS THE EXTENSION.
14. Do not use the nozzle on the gun directly.
15. The washer is supplied with lubrication close system,
so no addition of oil is needed.
To lubricate the o-rings use “GREASE FOR
BEARINGS”.
WARNING!
High pressure hoses, fittings and couplings are
important for the safety of the appliance.
Use only hoses, fittings and couplings recommended by the
manufacturer.
Only for the model provided with Total Stop System
(TSS): the pressure washer is equipped with a stop
device which will sense when the trigger on the gun is
released. It will open the power circuit to the motor and
cause the pressure washer to stop.
Remember not to use the TSS as a main switch.
16. NOZZLE CLEANING If the water jet is not regular
during the functioning or the thermic safety switch
switches off the machine, the nozzle is likely to be
blocked. Proceed as follows:
1. Remove plug from power socket.
2. High pressure can cause serious injury. Keep
spray head well clear of the face, other people,
animals or plants.
Protective clothing and goggles must be worn
during use.
3. Remove lance from the gun.
4. Using the tool provided, remove dirt from the
hole in the spray head and rinse well.
5. Perform a visual check through the nozzle to see
if all obstacles are removed.
ALWAYS USE THE FILTER SUPPLIED
17 Clean the filter Inspect periodically the suction filter
in order to avoid obstruction and damage to the
machine working.
Sand, limestone and furrings damage the pump
valves.
Priming soiled water invalidates the warranty !
STORAGE
- Switch off the cleaner. Turn off the water supply tap.
- Discharge residual pressure by pressing the trigger
until no more water comes out of the adjustable
nozzle.
- Engage the gun safety catch.
- Remove the plug from the socket.
- Operate the cleaner with noncorrosive/non-toxic
antifreeze before storing for the winter.
Ferm 5
,
.
Ferm
.
.
,
.
.
, ,
.
, , , .
.
o .
,
,
Ferm.
.
, .
.
.
.
:
EN 60335-2-79: 1998
98/37/CE
CEE 73/23, CEE 89/336
01-11-2002
GENEMUIDEN NL
W. Kamphof
Quality department
CE
ı
(
GR
)
48 Ferm
