Manual Ferm FDCS-185 (page 12 of 52) (English, German, Dutch, French, Italian, Norwegian)

110231

Zoom out

Zoom in

1/52

Ferm 93

RUNDSAV

Tallende i den følgende tekst korresponderer med afbildningerne på side 2 - 4.

Læs denne brugsanvisning godt igennem før maskinen tages i brug. Sørg for

at De kender maskinens funktion og betjening. Vedligehold maskinen i følge

instruktionerne, for at maskinen altid kan fungere optimalt. Bevar denne brug-

sanvisning og den vedlagte dokumentation til maskinen.

Indhold

1. Tekniske specifikationer

2. Sikkerhedsforskrifter

3. Montage og indstillings forskrifter

4. Betjening

5. Vedligeholdelse

1. TEKNISKE SPECIFIKATIONER

Tekniske data

Produktinformation

Fig. A

1. Håndtag

2. Tænd/sluk-kontakt

3. Spændeknap til skæredybde

4. Netledning

5. Sikkerhedsskærm til savklinge

6. Sekskantskrue

7. Bundplade

8. Stopring

9. Savklinge

10. Kløveanlægsflade

Spænding 230 V~

Frekvens 50 Hz

Optaget effekt 1200 W

Omdrejninger, ubelastet 5000/min.

Savklinge ∅185 x ∅20 x 2.4 mm

Tænder Z24

Maksimal savdybde 90° 65 mm

Maksimal savdybde 45° 43 mm

IP-klasse IP20

Vægt 4.05 kg

Lpa (lydtryk) 92.3 dB(A)

Lwa (lydeffekt) 103.3 dB(A)

Vibrationsværdi 4.689 m/s

12 Ferm

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine.

Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth moistened with soapy water. Never use sol-

vents such as petrol, alcohol, ammonia water, etc. These solvents may damage the

plastic parts.

Replacing hte carbon brushes

Fig. F

• Remove the screws (17).

• Withdraw the carbon brushes (18) from the circular handsaw and inspect them for

wear.

• Place the carbon brushes back in the brush holders provided.

• Check that the copper contact on the carbon brushes makes good contact with the

copper part in the brush holder.

• Replace the screws (17) and tighten them firmly.

Frequent use will cause the carbon brushes to wear down. Regular inspection,

after every 30 hours of use, is essential. If the brushes have worn down to less

than 4 mm, replace.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the

warranty card. In the back of this manual you find an exploded view showing the parts

that can be ordered.

• The tool does not work

when switched on.

• When cutting it is very

difficult to move the

work forward in a

straight line and the cut

is not clean.

• The circular saw

makes a lot of noise

and/or does not run

smoothly.

• Damaged cord and/or

plug.

• Defective switch.

• The blade is bent or

blunt.

• The carbon brushes

are worn.

• Check cord and/or

plug.

• Please contact the

service address on the

warranty card.

• Replace the blade.

• Please contact the

service address on the

warranty card.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCS-185 in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 5,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FDCS-185 Manual

Product: