Manual Ferm FDCD 1200 K (page 7 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

78862

Zoom out

Zoom in

1/108

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Charging the battery

• The included battery is delivered in partly

charged condition.

• Only use the battery charger in a temperature

range between + 5 °C to + 40 ºC.

• Only use the battery charger in dry, ventilated

rooms.

Charging

Fig. E

• Place the battery holder on a at table and put

the battery in the battery holder. Pay attention

to + and - pole markings.

• Put the adapter plug of the net adapter in the

connector on the side of the battery holder.

• Put the net adapter in the socket.

• The red charging lamp on the battery holder

will illuminate indicating the battery is being

charged.

• The charging process of a fully discharged

battery will take approximately 5 hours the rst

time and afterwards approximately 3 hours.

After the charging time the red light will

not switch off automatically! Remove the

battery within 5 hours from the charger.

If the battery is not removed from the

charger after the charging period it may

become overheated.

Discharging the battery

Not only charging batteries is important,

discharging is of equal importance or

even greater importance.

• When the battery is charged the cordless drill

has to be used until you start noticing that the

power of the drill is diminishing and that the

maximum rotational speed is not reached.

• The battery is almost discharged now. Only

now you can start charging the battery.

• Charging the battery while it is still charged for

say one-third of capacity, the so-called

‘memory effect’ can occur. Since during

charging only the discharged part of the

battery capacity of the battery is being charged

now, the battery can start crystallizing in the

one-third that is still charged. This part of the

battery capacity can never be used afterwards.

• Do not discharge the battery to the minimum.

As soon as you notice that the power or the

maxi-mum rotational speed is diminishing, you

have to charge the battery. When you proceed

using the drill and the battery becomes fully

discharged, the so-called ‘switch of poles

effect’ can occur. The polarity of the battery

poles will be switched: the ‘+’will become ‘-‘

and the ‘-‘ will become the ‘+’. Once this has

occurred the polarity will remain switched

during loading and this will damage the battery

irreparable.

When the cordless drill is not being used

over a longer period of time, the battery

has to be charged fully rst. The battery

has to be stored in charged condition.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly

clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation

slots free from dust and dirt. If the dirt does not

come off use a soft cloth moistened with soapy

water. Never use solvents such as petrol, alcohol,

ammonia water, etc. These solvents may damage

the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. Separate you nd an exploded

view showing the parts that can be ordered.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDCD 1200 K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm FDCD 1200 K Manual

Product: