78448

Ferm FDC 1200 K Manual

7
Zoom out
Zoom in
Previous page
1/30
Next page
• Movethedirectionreversingswitch(6)to
the centre in order to lock the appliance in
its disabled state.
Only lay down the appliance when it has
stopped running completely. Do not place it on
a dusty surface as particles of dust could get
into the mechanism.
Chargingthebattery
The included battery is delivered in non-
charged condition.
• Onlyusethebatterychargerina
temperature range between +5° to + 40º
Celsius.
• Onlyusethebatterychargerindry,
ventilated rooms.
Charging
Fig. E
• Placethebatteryholderonaflattableand
put the battery in the battery holder. Pay
attention to + and - pole markings.
• Puttheadapterplugofthenetadapterin
the connector on the side of the battery
holder.
• Putthenetadapterinthesocket.
• Theredcharginglamponthebattery
holder will illuminate indicating the battery
is being charged.
• Thechargingprocessofafullydischarged
battery will take approximately 5 hours the
first time and afterwards approximately 3
hours.
After the charging time the red light
will not switch off automatically!
Remove the battery within 5 hours
from the charger. If the battery is not
removed from the charger after the
charging period it may become
overheated.
Dischargingthebattery
Not only charging batteries is
important, discharging is of equal
importance or even greater
importance.
• Whenthebatteryischargedthecordless
drill has to be used until you start noticing
that the power of the drill is diminishing and
that the maximum rotational speed is not
reached.
• Thebatteryisalmostdischargednow.Only
now you can start charging the battery.
• Chargingthebatterywhileitisstillcharged
for say one-third of capacity, the so-called
‘memory effect’ can occur. Since during
charging only the discharged part of the
battery capacity of the battery is being
charged now, the battery can start
crystallizing in the one-third that is still
charged. This part of the battery capacity
can never be used afterwards.
• Donotdischargethebatterytothe
minimum. As soon as you notice that the
power or the maximum rotational speed is
diminishing, you have to charge the
battery. When you proceed using the drill
and the battery becomes fully discharged,
the so-called ‘switch of poles effect’ can
occur. The polarity of the battery poles will
be switched: the ‘+’will become ‘-‘ and the ‘-
‘ will become the ‘+’. Once this has
occurred the polarity will remain switched
during loading and this will damage the
battery irreparable.
When the cordless drill is not being
used over a longer period of time,
the battery has to be charged fully
first. The battery has to be stored in
charged condition.
5. SERVICE & MAINTENANCE
Make sure that the machine is not
live when carrying out maintenance
work on the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory
operation depends upon proper machine care
and regular cleaning.
• Sørgforatknappentilomløbsretningen(5
påfig.A)ståridenmidtersteposition,forat
undgåutilsigtetstartafmaskinen.
• Sætbatteriet(5)indimaskinenssokkel
somvistpåtegningen.Trykdetheltibund
sådetgårihak.
• Foratfjernebatterietskaldutrykke
låsekapperne(10)påbeggesiderindog
trække batteriet ud af maskinens sokkel.
4. BETJENING
Overholdaltidsikkerhedshenvisning
erne, og følg de relevante forskrifter.
Hold maskinen ordentligt fast, og tryk boret
ensartetindiemnet.Undgåatoverbelaste
maskinen. Anvend udelukkende bor som ikke
udviser synligt slid. Slidte bor har en negativ
indflydelsepåmaskinensfunktionsevne.
Indstilling af drejningsmoment
Fig. D
Maskinen har 16 forskellige indstillinger for
drejningsmoment til regulering af den kraft
hvormed skruer bliver skruet i eller ud.
• Sætindstillingsringenfordrejningsmoment
(3)idenønskedeposition.
De indstillinger af drejningsmomentet der
ertilrådighed,visespåindstillingsringen
dels med cifrene fra 1 til 8, dels med prikker
mellem cifrene som angiver
mellempositioner (dvs. i alt 16).
• Manskalhelstvælgedenlavesteposition
der giver tilstrækkelig kraft til at dreje
skruenrundt.Vælgenhøjerepositionhvis
motoren "glider i koblingen".
Anvendelse som skruetrækker.
• Sætknappenforomløbsretningen(6)i
position 'R' for at skrue skruer i.
• Sætknappenforomløbsretningen(6)i
position 'L' for at skrue skruer ud.
Boring
• Drejindstillingsringenfordrejningsmoment
(3) i boreposition.
Sørg for at knappen for
omløbsretningen (6) altid står i
position 'R' når du borer.
Start og stop
Fig. A
• Trykpåstartknappen(1).Dukanregulere
maskinens omdrejningstal ved at trykke
mereellermindrehårdtpåknappen.
• Nårduslipperstartknappen(1),bliver
patronen straks bremset, og der er ikke
nogetefterløb.
• Nårmaskinenerslukket,kandublokere
denvedatsætteknappenforomløbs-
retningen (6) i den midterste position.
Læg først maskinen fra dig når
motoren står helt stille. Læg ikke
maskinen på et støvet underlag. Der
kan trænge støv ind i mekanismen.
Opladning af batterier
Det vedlagte batteri er ikke opladet ved
leveringen.
• Brugkunbatteriopladerenved
temperaturer mellem +5º og + 40º Celsius.
• Brugkunbatteriopladerenitørre,udluftede
lokaler.
Opladning
Fig. E
• Sætbatteriholderenpåetplantbordog
sæt batteriet i batteriholderen. Vær op-
mærksompåmarkeringerneaf+og–pol.
• Sætnetadapterensadapterstikistikketpå
siden af batteriholderen.
• Sætnetadapterenistikkontakten.
• Denrødeopladningslampepå
batteriholderen lyser for at vise, at batteriet
er ved at blive opladet.
• Opladningenafetheltafladetbatteritager
cirka5timerførstegangogdereftercirka3
timer.
Det røde lys slukkes ikke auto-
matisk, når opladningstiden er forbi!
Tag batteriet ud af opladeren inden 5
timer. Hvis batteriet ikke tages ud af
opladeren efter opladningstiden, kan
det blive overophedet.
DK
54
Ferm Ferm
07
GB
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FDC 1200 K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FDC 1200 K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info