78131
12
Zoom out
Zoom in
Previous page
1/52
Next page
3. SAMLINGSANVISNING
Samlingsbetingelser
Det kræves måske, at du monterer sværd, savkæde og kædedæksel samt justerer kæden og fylder olie i beholderen på din nye kædesav, før
den er klar til brug. Start ikke motoren, før saven er rigtigt samlet. Læs alle instruktionerne omhyggeligt. Monter ikke nogen anden størrelse
sværd og kæde end den, der er anbefalet for din model.
Advarsel! Når du håndterer savkæden, bør du være iført handsker til beskyttelse mod skarpe kanter.
Montering af sværd / savkæde
Sådan monteres sværdet og savkæden :
1. Læg motorenheden på et fladt underlag.
2. For at fjerne sideskjoldet (A) skal knappen (B) og
skruen (C) drejes mod uret (Fig. 4a).
3. Skub sværdet på plads på saven og anbring kæden
korrekt på kædehjulet (Fig. 4b).
4. Læg kæden med de skærende kanter pegende i
rotationsretningen (Fig.4c).
5. Sæt sidedækslet på plads igen og drej knappen (B)
mod uret.
6. Drej tilspændingsringen (D), indtil kædespændingen er
korrekt (Fig. 4d + 5).
7. Når du har brugt saven i cirka en time, skal kædens
spænding justeres til 2 mm ved hjælp 9N
drejningsmoment.
Justering af savkædens spænding
Korrekt spænding af savkæden er meget vigtigt og skal kontrolleres
såvel før start som under savningen. Hvis man tager sig tid til at at
foretage de nødvendige justeringer, vil det resultere i forbedret ydelse
og forlænget levetid for kæden.
Bemærk: Hvis en kæde er for løs eller for stram, vil kæden og savens
lejer blive hurtigere slidt. Se Fig. 5 for at få information om den korrekte
koldspænding (A), den korrekte varmspænding (B) og for at få
retningslinier for, hvornår savkæden bør justeres (C).
Pas på! Hvis kæden er for løs, mere end 3mm efter at du
har trukket i den med en finger som vist på Fig. 5, skal den
justeres. Ellers vil standsningstiden overskride grænsen.
AB C
Fig. 5
Fig. 4d
DB
Fig. 4b Fig. 4c
E
Fig. 4a
CBA
Ferm 93
GB
D
NL
F
S
FIN
N
DK
As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in making straight cuts. Insufficient guide bar
lubrication and operating the saw with a chain that is too tight will contribute to rapid bar wear (see Section Chain maintenance instructions).
To help minimize bar wear, the following guide bar maintenance is recommended.
Bar wear
Turn guide bar frequently at regular intervals (for example, after 5 hours of use), to ensure even wear on top and bottom of bar.
Bargrooves
Bar grooves (or rails which support and carry the chain) should be cleaned if the saw has been heavily used or if the saw chain appears dirty.
Rails should always be cleaned every time the saw chain is removed.
Oil passages
Oil passages at bar pad should be cleaned to ensure proper lubrication of the bar and chain during operation. This can be done using a soft
wire small enough to insert into the oil discharge hole.
Note: The condition of the oil passages can be easily checked. If the passages are clear, the chain will automatically give off a spray of oil
within seconds of starting the saw. Your saw is equipped with an automatic oiler system.
Chain maintenance instructions
Warning! Unless you have experience and specialized training for dealing with kickback (see Safety Precautions), always use a
low-kickback saw chain, which significantly reduces the danger of kickback. Low-kickback saw chain does not completely
eliminate kickback. Alow-kickback or “safety chain”, should never be regarded as total protection against injury.
Alow-kickback saw chain should always be used in conjunction with other kickback protection devices such as the chain brake / Hand Guard
furnished with your unit. Always use a replacement saw chain designed as “low-kickback” or a saw chain which meets the low-kickback
performance. Astandard saw chain (a chain which does not have the kickback reducing guard links) should only be used by an experienced
professional chain saw operator.
What is a Low-Kickback Saw Chain
Alow-kickback saw chain is a chain which has met the kickback performance requirements of ISO 9518.
By keeping the chain brake and saw chain in good working condition and correctly serviced as recommended in this manual, you will be able
to maintain the safety system of your chain saw over the life of the product.
Warning! Never remove, modify or make inoperative any safety device furnished with your unit. The Chain Brake/Hand Guard
and low-kickback saw chain are major safety features provided for your protection.
Warning! Always wear heavy duty protection work gloves and disconnect the extension cord when working on the saw chain.
Chain sharpening
A. General information about sharpening the chain
Never saw with a blunt chain. The chain is blunt when you have to push the chain saw into the tree and the chips are
very small. The saw-link is the part of the chain which does the sawing (Fig. 17). The height-distance between the
tooth Aand the ridge B is the cutting-depth. When sharpening the chain you have to consider the next points
(Fig.18):
File-angle
Cutting-angle
File-position
Diameter of round file
File-depth
For correct sharpening of the chain you need good tools; for example a mould to obtain a correct file-angle.
Fig. 17
A
B
12 Ferm
GB
D
NL
F
S
FIN
N
DK
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm FCS 2000 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm FCS 2000 S in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 11,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info