Manual Ferm fbh 1100 k (page 13 of 42) (English, German, Dutch, French, Italian)

388809

Zoom out

Zoom in

1/42

Ferm 13

2. EIN-/AUS-Schalter

3. Handgriff

4. Umschaltung Betriebsart

5. Kohlbürstenkappe

6. Netzkabel

7. Zusatzhandgriff

8. Bohrtiefenanschlag

9. Staubkappe

10. Bohrhammer

11. Verriegelung

12. Schmierdeckel

2. SICHERHEITSHINWEISE

In dieser Bedienungsanleitung werden die folgenden Symbole verwendet:

Anweisungen sorgfältig lesen

Übereinstimmung mit den jeweils maßgeblichen EU-Sicherheitsrichtlinien

Gerät der Schutzklasse II – schutzisoliert – kein Schutzkontakt erforderlich

Lebens- und Verletzungsgefahr und Gefahr von Beschädigungen am Gerät bei

Nichteinhaltung der Sicherheitsvorschriften in dieser Anleitung.

Deutet das Vorhandensein elektrischer Spannung an.

Ziehen Sie, falls das Kabel beschädigt wird und auch während Wartungsarbeiten,

sofort den Netzstecker.

Schutzbrille und Gehörschutz tragen

Schadhafte und/oder entsorgte elektrische oder elektronische Geräte müssen an

den dafür vorgesehenen Recycling-Stellen abgegeben werden.

Zusätzliche Sicherheitshinweise

• Tragen Sie Ohrenschützer. Die Lärmbelastung kann zu Gehörschäden führen.

• Verwenden Sie die im Lieferumfang enthaltenen Zusatzgriffe.

Durch Kontrollverlust kann es zu VerletzungenFür den Gebrauch dieses Elektro-

werkzeuges:

• Kontrollieren Sie die zu bohrende Stelle auf versteckte Elektrokabel, Gasleitungen oder

andere Hindernisse (z. B. mit einem Metalldetektor).

72 Ferm

4. VEDLIKEHOLD

Pass på at maskinen ikke er koplet til strømtilførselen når du utfører vedlikehold på

mekaniske deler.

Maskinene er utformet for problemfri funksjon over lang tid med minimalt med vedlikehold.

Ved å rengjøre maskinen regelmessig og behandle den riktig, bidrar du til å sørge for en lang

levetid.

Defekter

Maskinen må undersøkes regelmessig for følgende mulige defekter og repareres om

nødvendig.

• Skade på strømledningen

• Ødelagt på/av-bryterenhet

• Kortslutning

• Skadede bevegelige deler

Feilsøking

• Motoren går ikke når

verktøyet slås på.

• Motoren avgir kraftig

støy og går for sakte eller

ikke i det hele tatt.

• Overoppheting i

transmisjonen.

• Svikt i strømtilførselen.

• Dårlig kontakt i på/av-

bryteren.

• Tilførselsspenningen er

for lav.

• Skadet motor.

• Karbonbørstene er slitt.

• Motoren er overbelastet

på grunn av for kraftig

trykk eller for stor

drilldybde.

• Skadet motor.

• Tilførselsspenningen er

for lav.

• Karbonbørstene er slitt.

• Overbelastning av

maskinen eller sløv

drillbit.

• Kontroller

strømtilførselen.

• Reparer eller bytt på/av-

knappen.

• Skjøteledningen er for

lang eller for tynn.

• Få en ekspert til å

reparere maskinen.

• Bytt karbonbørstene.

• Reduser trykket eller

drilldybden, reduser

kraften.

• Få en ekspert til å

reparere maskinen.

• Juster

tilførselsspenningen.

• Bytt karbonbørstene.

• Reduser belastningen

eller slip drillbiten.

I have a Ferm HDM1100/FDH4004. I have had it from new and it still works perfectly. The problem I have is with the handle. I need part number 28 which fits around the drill collar. Are they available and if so can you advise me where I can get it? Submitted on 28-7-2019 at 15:08
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fbh 1100 k in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm fbh 1100 k Manual

Product: