391290

Ferm fag 125 1050 Manual

8
Zoom out
Zoom in
Previous page
1/84
Next page
EN
8
Ferm
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1,5 mm
2
. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Assembling the hand grip
Fig. 1
The hand grip is suitable for either left or right-
handed use.
Turn the hand grip (3) to the notch on the right •
side of the machine for left-handed use.
Turn the hand grip (3) to the notch on the left •
side of the machine for right-handed use.
Turn the hand grip to the notch on the top of •
the machine to use it vertically.
Mounting a grinding disc
Fig. 2
Use grinding discs of the correct dimension. Use
fibre reinforced grinding discs only.
The grinding disc must not touch the edge of the
guard.
Press the spindle lock (6) and turn the spindle •
(9) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
Remove the flange nut (12) from the spindle •
using the spanner (11).
Position the grinding disc (7) on the flange (5).•
Place the flange nut on the spindle an tighten •
it using the spanner.
Release the spindle lock and check that the •
spindle is unlocked by rotating it.
Mounting grinding discs and roughing discs
Fig. 3 and 4 show how to mount the flange (10)
when using thick (4 - 8 mm) and thin
(2,5 - 4 mm) discs.
The following grinding discs can be used with this
grinder.
For deburring: grooved, fibreglass reinforced •
type 27. Dimensions Ø 125x6.0x22.2 mm.
For slitting/ cutting: grooved, fibreglass •
reinforced, type 41 and type 42. Dimensions
Ø 125x3.0x22.2 mm.
If you use normal grinding discs they
should always be fibreglass reinforced.
4. USE
Always follow the safety instructions
and keep to the applicable regulations.
Hold the machine away from the workpiece when
turning it on and off because the grinding disc
could damage the workpiece.
Clamp the workpiece firmly or use another •
method to ensure that it cannot move while
working.
Check the discs regularly. Worn grinding discs •
have a negative effect on the machine’s
efficiency. Change to a new grinding disc in
good time.
Always first turn the machine off after use •
before removing the plug from the socket.
Deburring
Fig. 5
An angle of inclination of 30º to 40º will give the
best results when deburring. Move the machine
back and forth using light pressure. This will
prevent the workpiece from discolouring or
becoming too hot and will avoid making groves.
Never use abrasive cutting discs for
deburring work!
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm fag 125 1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm fag 125 1050 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 10,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info