510093
4
Zoom out
Zoom in
Previous page
1/60
Next page
EN
4
result in unexpected firing of fasteners and
personal injury.
 Do not point the tool towards yourself or
anyone nearby. Unexpected triggering will
discharge the fastener causing an injury.
 Do not actuate the tool unless the tool is
placed firmly against the workpiece. If the tool
is not in contact with the workpiece, the
fastener may be deflected away from your
target.
 Disconnect the tool from the power source
when the fastener jams in the tool. While
removing a jammed fastener, the tacker may
be accidentally activated if it is plugged in.
 Do not use this tacker for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
Before using the tacker
 Check the following points:
• Do the voltage of the engine and the
engine safe-guard, if any, correspond to
the mains voltage (appliances for a mains
voltage of 230 V);
• Are the mains lead and the mains plug in
a good condition: solid, without any loose
ends or damage.
 Always wear eye protection when using the
tool.
 Maintain the tool with care.
 Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tools operation. If
damaged, have the tool serviced before
using.
 Check if the slide cartridge has been fastened
properly.
 Do not use the tool in a humid environment.
 Do not use the tool on materials containing
asbestos.
Using the tool
 Do not use the tool if the switch does not turn
it “ON” or “OFF”.
 Always hold the tool with two hands while
starting.
 Always keep the cord away from the moving
parts of the machine.
 Keep your hands away from the work piece.
 In the case of jamming by a nail or staple,
switch the machine off immediately and
remove the plug from the mains.
 Never aim the tool at people or animals.
 Use only staples or nails fit for this tool.
 Make sure not to damage any leads when
using the tool.


When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double
insulated; therefore no earthwire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.

Application
Fig. 2
For this tool, use one of the following types
staples or nails:
 U: 6, 8, 10, 12, 13 or 14 mm
 T: 15 mm
 I: 15 mm
Suitable staples and nails are provided by:

Rapid: R11, R54, R14, R34, R114, R64
Piranha: 5, 13
Novus
www.servotool.eu
Loading the tacker
Before opening the tool, make sure the
tool is disconnected.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm ETM1003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ETM1003 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info