763829
7
Zoom out
Zoom in
Previous page
1/92
Next page
7
EN
USE

To switch on the machine, press the on/off
switch (1).
To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
To switch off continuous mode, press the
on/off switch (1) again.
To switch off the machine, release the
on/off switch (1).

The speed adjustment wheel is used for setting the
speed. The speed adjustment wheel can be set to 6
positions. The ideal speed depends on the required
grain size and on the material to be worked.
2
Do not set the speed during use.
Turn the speed adjustment wheel (3) to the
required position.
- For hard materials, use sanding paper with
a ne grain size and select a lower speed.
- For soft materials, use sanding paper with a
coarse grain size and select a higher speed.

Insert the dustbag (9) into the dustbag
connection (7).
Turn the dustbag (9) clockwise until it locks
into place.
Hints for optimum use
Clamp the workpiece.
Firmly hold the machine with both hands.
Switch on the machine.
Place the sanding pad with sanding paper on
the workpiece.
Slowly move the machine over the workpiece,
rmly pressing the sanding pad against the
workpiece.
Do not apply too much pressure on the
machine. Let the machine do the work.
Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
4 Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
Regularly clean the housing with a soft cloth.
Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
Regularly clean the sanding pad to avoid
inaccuracies during use.

To remove the old sanding paper (8), proceed
as described in the section
„Mounting and removing the sanding paper“.
To mount the new sanding paper (8), proceed
as described in the section
„Mounting and removing the sanding paper“.

In case of wear, the sanding pad must be replaced.
If necessary, remove the sanding paper.
Loosen the screws (10) from the sanding pad
(4).
Remove the old sanding pad (4).
Mount the new sanding pad (4).
Tighten the screws (10) to the sanding pad (4).
WARRANTY
Consult the enclosed warranty terms.
ENVIRONMENT
Disposal
8
The product, the accessories, and the packaging
must be sorted for environmentally friendly
recycling.
Only for EC countries
Do not dispose of power tools into domestic
waste. According to the European Guideline
2002/96/EC for Waste Electrical and Electronic
Equipment and its implementation into national
right, power tools that are no longer usable must
be collected separately and disposed of in an
environmentally friendly way.
The product and the user manual are subject to
change. Specications can be changed without
further notice.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm ESM1007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ESM1007 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info