Manual Ferm CTM1009 - FCT-300 (page 6 of 36) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763699

Zoom out

Zoom in

1/36

06 Ferm

Always check that the power supply corresponds to the voltage on the rating plate.

The machine is double insulated in accordance with EN50144; therefore no earth

wire is required.

Replacing cables or plugs

If the mains cable becomes damaged, it must be replaced with a special mains cable available

from the manufacturer or the manufacturer’s customer service. Dispose of old cables or plugs

immediately after replacing them with new ones. It is dangerous to connect the plug of a loose

cable to a socket.

Using extension cables

Only use an approved extension cable suitable for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely.

Assembly of accessories

Fig. 1

Before assembly always remove the plug from the mains.

Warning! Change accessories by inserting an accessory into the collet (or chuck)

as far possible to minimize run out and unbalance.

Press down the axle locking button (2) and hold it down. Using the spring chuck spanner you

can undo the spring chuck (1). Put the accessory in its place. Hold down the axle locking

button when you fasten the spring chuck with the spring chuck spanner.

Operation

Switch on the machine by engaging the on/out switch (A) By adjusting the adjusting wheel (B)

you can regulate the speed of the Combi tool. Do not put the machine down when the motor is

still running. Do not place the machine on a dusty surface. Dust particles may enter the

mechanism.

Too high a load at a low speed of the Combi tool can burn out the engine.

Accessories for the Combitool

Ferm does not deliver spare accessories for the Combitool. The Combitool is designed to use

the standard accessories of Dremel, Black & Decker, Bosch or Proxxon. Always check that the

maximum rpm of the accessory is suitable for the maximum speed of the Combitool.

3.ASSEMBLY OF ACCESSORIES

Ferm 67

Før et stykke tilbehør bruges, skal man altid kontrollere, om tilbehørets tilladte omdrejningstal

kan tåle Combitool’s maksimale hastighed.

Slibesten

Fig. 2

Hvis en slibesten skal bruges for første gang, skal man bruge vådstenen til afbalancering af

slibestenen. Vådstenene kan også bruges for at give slibestenen en speciel form.

Materiale Hastighed

Sten, skal 1

Stål 5

Aluminium,messing 2

Plastic 1

Filtskiver og -spids

Fig. 3

Tilbehør af filt skal monteres på akslen, der medføger.

Materiale Hastighed

Stål 5

Aluminium,messing 2

Plastic 1

Filtskiver og -spids: Slibebånd og -skiver

Fig. 4

Materiale Hastighed

Træ 6

Stål 1

Aluminium,messing 3

Plastic 1

Børster af rustfrit stål og børster, der ikke er af metal

Fig. 5

Materiale Hastighed

Sten, skal 2

Aluminium,messing 2

Fræsebit, graverspids og bor

Fig. 6

Materiale Hastighed

Træ Max

Stål 3

Aluminium,messing 6

Plastic 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CTM1009 - FCT-300 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CTM1009 - FCT-300 Manual

Product: