Manual Ferm CSM1043 (page 10 of 140) (All languages)

762265

Zoom out

Zoom in

1/140

Attachment of the parallel guide

Fig. 3

• Attach the parallel guide (12) on the right side

of the machine, as shown in Fig. 3

• Lock the guide down by turning the

adjustment knob (13) clockwise.

4. OPERATION

Unplug the machine before mounting

any accessories!

Adjusting the sawing depth

Fig. 1, 5

The sawing depth can be adjusted with the saw

depth limiter.

• Loosen the saw depth limiter (3) using the hex

key (17) and move the saw depth limiter to the

required saw depth. The sawing depth ‘A’ is

shown in Fig. 5B. The depth indicator has long

lines to indicate even milimeters and short

lines to indicate odd milimeters.

• Tighten the saw depth limiter (3) using the hex

key (17).

Indications:

• For optimal result when sawing wood, the

cutting depth should be set slightly greater

than the thickness of the chosen material.

• When cutting plastic, the cutting depth should

also be greater than the thickness of the

material. If the material begins to melt, then

setting a greater depth of cut usually resolves

the problem.

• When cutting metal, the cutting depth should

be at least 1.0 mm larger than the thickness of

the material.

• When sawing wood or plastic, the depth of cut

can also be set exactly on the thickness of the

material to prevent that the underlying surface

gets damaged. However, this does lead to an

impure saw cut at the bottom of the workpiece

Blade replacement without removing the guard

Fig. 4

Incorrect positioning of the blade can

permanently damage the tool. Always

wear protective gloves to prevent injury!

1. Press the spindle lock button (14) to prevent

the saw from turning. (Fig. 4A)

2. Keep the spindle lock button (14) pressed and

loosen the clamping nut (16) using the hex key

(17). (Fig. 4B)

3. Remove the mounting flange (15)

4. Loosen the saw depth limiter (3) using the hex

key (17) and press the guard to remove the

blade. (Fig. 4C)

5. Keep the guard pressed and place the new

blade onto the blade shaft. Ensure the hole

locates correctly and the teeth point in the

direction of the curved arrow. (Fig. 4C)

6. Place the mounting flange (15) insuring the

long sides of the mounting flange correspond

with the long sides of the blade shaft.

7. Press the spindle lock button (14) pressed and

tighten the clamping nut (16) using the hex key

(17). (Fig. 4D)

8. Make sure the blade rotates smoothly by

rotating the sawblade at least one turn. Check

if the guard functions correctly.

9. The machine can now be used again.

Holding and turning on the saw

Fig. 1

Holding the saw correctly makes the work lighter,

cleaner and safer.The Precision Circular Saw is

only suitable for right-handed use.

• Slide the on-/off switch (4) forward.

• Release the on-/off switch to switch the

machine off

Speed Adjustment

Fig. 1

The required speed can be adjusted by using the

Speed adjustment knob (7). Also during running

the rotational speed can be adjusted.

• To increase the speed, turn the Speed

adjustment knob (7) clockwise.

• To decrease the speed, turn the Speed

adjustment knob (7) anti-clockwise.

The required speeds depends on the material

and can be determined by practical testing.

Clamping

It is not normally necessary to clamp the material

being cut as long as it is fully supported on a work

surface and held with one hand. Clamping should

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1043 in the language / languages: All languages as an attachment in your email.

The manual is 8,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1043 Manual

Product: