Manual Ferm CSM1035 (page 9 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763368

Zoom out

Zoom in

1/132

Class ll machine. Your machine is double

insulated; therefore no earthwire is

required.

If the replacement of the supply cord is necessary,

this has to be done by the manufacturer or his

agent in order to avoid a safety hazard.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

3. Operation

Unplug the machine before mounting any

accessories!

Adjusting the sawing depth

Fig. 1

The sawing depth can be adjusted with the saw

depth limiter.

Loosen the screw (3) and move the saw depth •

limiter to the required saw depth. The depth

indicator has long lines to indicate even

milimeters and short lines to indicate odd

milimeters.

Tighten the screw.•

For the best result when sawing wood and plastic,

the sawing depth much be slightly greater than

the thickness of the material. When sawing metal,

the sawing depth must be 1.0 mm greater than the

thickness of the material.

Blade replacement without removing the

guard

Fig. 2 -5

Incorrect positioning of the blade can

permanently damage the tool. Always

wear protective gloves to prevent injury!

1. Without removing the guard insert one

hex key into the blade shaft to lock it (Fig.

2). Insert the other hex key into the blade

retaining screw and unscrew clockwise (Fig.

3). Remove the cover.

2. Unscrew the depth adjuster and depress the

guard to remove the blade.

3. Place the new blade onto the blade shaft

ensuring the hole locates correctly and the

teeth point in the direction of the curved arrow

(Fig. 4).

4. Replace the safety retaining washer and

tighten the screw.

5. Remove the hex key. Make sure the blade

rotates smoothly by rotating the sawblade at

least one turn. Place the cover back in place.

Remove the hex key. Make sure the blade

rotates smoothly. Place the cover back in

place.

6. Remove the second hex key and check if the

guard functions correctly.

7. The machine can now be used again.

Adjusting the length

Fig. 9

In order to saw neatly, it is important to know

where the saw must start and finish. There are

numbers on both sides of the protective cover

which correspond to the sawing depth settings

and which indicate the start and finish points of

the blade.

Mark where the material is to be sawn. If the •

area to be sawn is not square or rectangular,

the start and finish lines must be indicated

separately. These points must be drawn

perpendicular to the sawing line.

In order to use the length setting, the sawing •

depth must first be set as described

previously. Set it to, for example, 2 mm. Find

the number, in this case 2, at the front and

back of the protective cover.

Make sure the line under the number is align ed •

with the starting point of the line to be sawn.

Saw until the line under the number at the •

front of the cover is aligned with the end point

of the line to be sawn.

The length indicator has lines for even •

milimeters (2-4-6-8-10-12).

Holding and turning on the saw

Fig. 6

Holding the saw correctly makes the work lighter,

cleaner and safer.The Precision Circular Saw is

only suitable for right-handed use.

Slide the on-/off switch(4) forward.•

Release the on-/off switch to switch the •

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1035 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1035 Manual

Product: