763365
5
Zoom out
Zoom in
Previous page
1/68
Next page
GB
5
Ferm
guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and
make sure it moves freely and does not touch
the blade or any other part, in all angles and
depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) Lower guard should be retracted manually
only for special cuts such as plunge cuts”
and “compound cuts.” Raise lower guard
by retracting handle and as soon as blade
enters the material, the lower guard must
be released. For all other sawing, the lower
guard should operate automatically.
d) Always observe that the lower guard is
covering the blade before placing saw down
on bench or floor. An unprotected, coasting
blade will cause the saw to walk backwards,
cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch
is released.
Before using the circular saw
Check the following points:
Does the voltage of the motor correspond •
with the mains voltage (appliances for a
mains voltage of 230 V
Are the mains lead and the mains plug in •
a good condition: solid, without any loose
ends or damage;
Is the saw blade missing any teeth or •
showing any cracks, it so must be
replaced immediately.
Make sure the blade is secure.•
Use this circular saw to saw only wood, •
wood-like products.
Do not use circular saw blades wich are •
deformed or damaged.
Do not use HSS blades.•
Only use blades meeting the required •
dimensions, as well as data and descriptions;
Never apply any blades of which the thick-•
ness is greater than that of the riving knife.
Do not stop the blade of a circular saw by •
pressing the blade from the side.
Check that the blade guard can freely move •
and fully closes.
Never lock-up the guard in the open position.•
Never put sideward pressure on the blade. •
This may cause the blade to break.
Be careful when cutting wood with knots, •
nails or cracks in it and/or dirt on it, as these
can cause the blade to get stuck.
Never leave the circular saw unattended.•
Use this circular saw to saw only wood or •
wood-like products.
Using the machine
Use clamps or a vice to hold the work.•
Never remove wood chips and saw dust that •
is close to the saw blade with your hands. If
there are small pieces of wood left between
the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs
to be removed from the socket, before any left
piece can be removed.
Check that the blade is suitable for the •
spindle speed of the circular saw. Do not
attempt to cut before the circular saw has
reached full speed. Make sure the circular
saw runs without load (i.e. is not in contact
with the work) when you switch it on. The
circular saw must have reached its full speed
first.
Never cut wood that is thicker than the depth •
of the saw blade.
When cutting in wooden walls or floors, check •
there is no wiring or piping where you intend
to cut.
Switch off the tool and wait until the blade has •
stopped completely before moving the saw
away from the work or putting it down.
Hearing protection should be worn when
using circular saw.
Switch off the machine immediately when you
discover:
A defective mains plug or mains lead;•
A defective switch.•
Overheating of the circular saw.•
Smoke or odeur caused by scorched •
insulation.
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and
personal injury. Read the following safety
instructions and also the enclosed safety
instructions. Keep these instructions in a safe
place!
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CSM1032 - FKS-165 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1032 - FKS-165 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info