Manual Ferm CSM1028 FPCS-1800 (page 7 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

539085

Zoom out

Zoom in

1/56

Ferm

Before using the circular saw

Check the following points:

Is the saw blade missing any teeth or showing •

any cracks, it so must be replaced

immediately.

Make sure the blade is secure.•

Use this circular saw to saw only wood, wood-•

like products.

Do not use circular saw blades which are •

deformed or damaged.

Do not use HSS blades.•

Only use blades meeting the required •

dimensions, as well as data and descriptions;

Do not stop the blade of a circular saw by •

pressing the blade from the side.

Check that the blade guard can freely move •

and fully closes.

Never lock-up the guard in the open position.•

Never put sideward pressure on the blade. •

This may cause the blade to break.

Be careful when cutting wood with knots, nails •

or cracks in it and/or dirt on it, as these

can cause the blade to get stuck.•

Never leave the circular saw unattended.•

Use this circular saw to saw only wood or •

wood-like products.

Using circular saw.

Use clamps or a vice to hold the work.•

Never remove wood chips and saw dust that is •

close to the saw blade with your hands. If

there are small pieces of wood left between

the fixed and the movable parts, the circular

saw will have to be stopped. The plug needs

to be removed from the socket,

before any left piece can be removed.•

Check that the blade is suitable for the spindle •

speed of the circular saw. Do not attempt to

cut before the circular saw has reached full

speed. Make sure the circular saw runs

without load (i.e. is not in contact with the

work) when you switch it on. The circular saw

must have reached its full speed first.

Never cut wood that is thicker than the depth •

of the saw blade.

When cutting in wooden walls or floors, check •

there is no wiring or piping where you intend to

cut.

Switch off the tool and wait until the blade has •

stopped completely before moving the

saw away from the work or putting it down. •

Hearing protection should be worn when

Safety tips for the laser beamer

Never look into the light beam of the laser.•

Never point the light beam of the laser at •

humans or animals.

Do not point the light beam of the laser at •

strongly reflecting material. Hazard from

reflected light.•

Only have repairs made to the laser beamer •

by qualified personnel / professional repair

specialists.•

Do not insert any hard objects into the laser •

optics.

Clean the laser optics with a soft, dry brush.•

Switch off the machine immediately when you

discover:

A defective switch.•

Overheating of the circular saw.•

Smoke or odour caused by scorched •

insulation.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Setting the sawing angle (bevel)

Fig. B

Loosen the saw angle clamping knob (11).•

Rotate the soleplate (6) in the correct position •

(0º - 50º) and tighten the saw angle clamping

knob. The sawing angle (bevel) can be read

on the protractor (10).

Fitting the rip fence

Fig. C

Loosen the rip fence clamping knob (12).•

Insert the rip fence into the slots provided.•

Set the correct cut width and thighten the rip •

fence clamping knob (12).

Setting the cutting depth

Fig. D

Pull out and loosen the cut depth clamping •

knob by turning it counter clockwise (16).

Caution! Do not turn the cut clamping

knob more than 1 full turn.

Move the soleplate (6) downwards.•

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CSM1028 FPCS-1800 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CSM1028 FPCS-1800 Manual

Product: