Ferm 67
• Tryk derefter på knappen (A). Rundsaven
starter nu.
• Rundsaven stopper, når du slipper knappen
(A).
Ibrugtagning
• Klem arbejdsemnet fast, således at begge
hænderne er fri til at fastholde og betjene
rundsaven.
• Tilkobl rundsaven og placér savebunden på
arbejdsemnet.
• Tryk forsigtigt på rundsaven og bevæg den
langsomt frem langs den på forhånd tegnede
skærelinie.
• Tryk savebunden fast mod arbejdsemnet.
Lad rundsaven gøre arbejdet! Undlad
derfor at udøve for meget tryk på
rundsaven.
Laser lys
Laser lyset i brug
Det ledende laser lys gør det meget lettere at
save i lige linjer:
a) Langs en optegnet linje, eller
b) Ved at stille det på linje med at fast punkt
markeret på objektet.
Laser lysets rækkevidde, afhængig af det
omkringværende lys, er omkring 65 cm.
Placering af batterier
• Hold den cirkelformede håndsav ligefrem
foran Dem. Løft låget på laserlyset mod Dem
selv og løft dette. Byt de gamle batterier med
nye. De skal bruge 2 x 1.5 V “Mikro/AAA”
batterier.
• Smid aldrig gamle batterier ud med
køkkenaffaldet, men aflever dem i stedet til et
specielt batteri eller kemikali afleveringsdepot.
• Når De isætter batterierne, sikre Dem at +/-
terminalen er korrekt placeret som vist inde i
batterirummet.
• Igen skal De trykke ned på låget, skubbe det
mod Dem selv, trykke mod savbladets låg og
lade det blødt springe tilbage til den lukkede
position.
• Check at laser lyset er korrekt lukket ved
forsigtigt at åbne låget opad. Hvis låget åbner,
skal De gentage lukke proceduren indtil låget
forbliver korrekt lukket.
Justering af laser lyset
• Behandling ved transport og ofte brug kan
påvirke laser lysets præcision.
• Laser lyset i sig selv kan let blive justeret.
• Hold bladet af den runde sav mod en lige kant
eller perfekt lige planke.
• Tænd for laser lyset.
• Check om laser lyset løber parallel med
kanten eller plankens kant.
• Hvis laser lyset ikke løber parallel, gør da
følgende:
• Løs de to skruer foran på laseren et par
omdrejninger.
• Hold bladet på rundsaven mod en lige kant
eller perfekt lige planke.
• Juster laseren sådan at den løber
fuldstændigt lige med kanten.
• Fastskrue de to skruer igen.
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under
strøm, når der udføres
vedligeholdelsesarbejder på
mekanikken.
Maskinerne er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse.
Ved at rengøre maskinen regelmæssigt og
behandle den korrekt, bidrager De til en længere
levetid for maskinen.
Fejl
Hvis rundsaven ikke virker hensigtsmæssigt, kan
du gennemgå følgende mulige årsager og
tilhørende løsninger for at afhjælpe problemerne.
1. Elektromotoren overophedes.
• Motoren overbelastes, fordi der saves for
store arbejdsemner.
• Sav i et lavere tempo og lad motoren køle
af.
• Motoren er defekt.
• Kontakt venligst serviceadressen på
garantibeviset.
2. Maskinen virker ikke, selv om den er
tilkoblet.
• Fejl i netledningen.
• Kontrollér netledningen for brud.
• Afbryderen er defekt.
• Kontakt venligst serviceadressen på
garantibeviset.
DK
06 Ferm
Be aware of the time it takes for the blade to
stop after switch is released.
Before using the circular saw
• Check the following points:
• Does the voltage of the motor correspond
with the mains voltage (appliances for a
mains voltage of 230 V
• Are the mains lead and the mains plug in a
good condition: solid, without any loose
ends or damage;
• Is the saw blade missing any teeth or
showing any cracks, it so must be replaced
immediately.
• Make sure the blade is secure.
• Use this circular saw to saw only wood,
wood-like products.
• Do not use circular saw blades wich are
deformed or damaged.
• Do not use HSS blades.
• Only use blades meeting the required
dimensions, as well as data and descriptions;
Never apply any blades of which the thickness
is greater than that of the riving knife.
• Do not stop the blade of a circular saw by
pressing the blade from the side.
• Check that the blade guard can freely move
and fully closes.
• Never lock-up the guard in the open position.
• Never put sideward pressure on the blade.
This may cause the blade to break.
• Be careful when cutting wood with knots, nails
or cracks in it and/or dirt on it, as these can
cause the blade to get stuck.
• Never leave the circular saw unattended.
• Use this circular saw to saw only wood or
wood-like products.
Using the machine
• Use clamps or a vice to hold the work.
• Never remove wood chips and saw dust that
is close to the saw blade with your hands. If
there are small pieces of wood left between
the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs
to be removed from the socket, before any left
piece can be removed.
• Check that the blade is suitable for the spindle
speed of the circular saw. Do not attempt to
cut before the circular saw has reached full
speed. Make sure the circular saw runs
without load (i.e. is not in contact with the
work) when you switch it on. The circular saw
must have reached its full speed first.
• Never cut wood that is thicker than the depth
of the saw blade.
• When cutting in wooden walls or floors, check
there is no wiring or piping where you intend
to cut.
• Switch off the tool and wait until the blade has
stopped completely before moving the saw
away from the work or putting it down.
Hearing protection should be worn when
using circular saw.
Switch off the machine immediately when you
discover:
• A defective mains plug or mains lead;
• A defective switch.
• Overheating of the circular saw.
• Smoke or odeur caused by scorched
insulation.
Safety tips for the laser beamer
• Never look into the light beam of the laser.
• Never point the light beam of the laser at
humans or animals.
• Do not point the light beam of the laser at
strongly reflecting material. Hazard from
reflected light.
• Only have repairs made to the laser beamer
by qualified personnel / professional repair
specialists.
• Do not insert any hard objects into the laser
optics.
• Clean the laser optics with a soft, dry brush.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the power supply
corresponds to the voltage on the rating
plate.
The machine is double insulated;
therefore no earth wire is required.
Replacing cables or plugs
If the mains cable becomes damaged, it must be
replaced with a special mains cable available
from the manufacturer or the manufacturer’s
customer service.
GB
