Manual Ferm CRM1045 (page 7 of 64) (English, German, Dutch, French, Polish)

632691

Zoom out

Zoom in

1/64

to the instructions represented in fig. 2. Place the

compressor on a flat surface or at a maximum slope

of10°(fig.3),inawellventilatedarea,protected

against atmospheric factors and not in explosive

surroundings.Ifthesurfaceareaisslopingand

smooth,makesurethatthecompressorwillnot

movewheninoperation.Ifthesurfaceareaisa

boardorashelfofabookcase,justmakesurethat

they cannot fall down by securing them properly.

Forproperventilationandeffectivecooling,itis

important that the compressor is positioned at least

100 cm from the wall (fig. 4).

Make sure that the compressor is

transported in the right way, do not turn it

upside down and don’t lift it with hooks

or ropes (fig. 5-6).

Filling the compressor with oil.

Your compressor is supplied with oil which is

already included in the carter.

Beforeuse,removethetransportcaponthecarter

(12),andreplaceitbytheregularoilcap(fig7).

Beforeuse,ensurethatoillevelissufficient.

This can be checked by checking the oil

inspectionglass(13).Whencompressorisplaced

horizontally,theoillevelshallreachtheredmark.

Installing the air filters.

Remove the transport lids and replace them with

the supplied air filters before using the compressor.

Starting up

• Checkwhetherthemainsvoltagecorresponds

to that indicated on the electrical specification

plate(fig.10),thepermittedtolerancerange

should be within 5%.

• Presstheswitch(3)situatedontheupperpart

intothe“0”positionaccordingtothepressure

regulator type fitted on the device (fig. 11).

• Puttheplugintheplugsocket(fig.9)andstart

the compressor up by putting the switch(3)

ofthepressureregulatorinthe“I”position.

The operation of the compressor is fully

automatic. The pressure regulator will stop

the compressor when the maximum value has

been reached and start it up when the pressure

drops below the minimum value. Normally

the difference in pressure is approx. 2 Bar/29

psi between the maximum and the minimum

value.Forinstance-Thecompressorwillstop

when it reaches 8 Bar (116 psi) (this is the

maximum operating pressure) and will start

up automatically when the pressure within the

tank has dropped to 6 Bar (87 psi).

The head/cylinder/transmission pipe

assembly may reach high temperatures,

so take care when working close to these

parts and do not touch them to avoid

burns (fig. 12 - 13).

Adjusting the operating pressure

Fig. 14

Itisnotnecessarycontinuouslytousethe

maximumoperatingpressure,thecompressed-air

toolsoftenrequirelesspressure.Withregardto

compressors supplied with a pressure reduction

valve it is necessary to set the operating pressure

properly.

Itispossibletosettheoperatingpressureby

using the turning knob(5) on the reduction valve.

• Byturningclockwise,thepressurewillbe

increased.

• Byturninganti-clockwise,thepressurewillbe

reduced.

The compressor has two pressure gauges and

onepointtoconnectanairhose:

• Pressuregauge(7):Thepressureofthisoutlet

can be regulated with help of the reduction

valve (5).

• Pressuregauge(8):tankpressure

Hintsforaccurateadjustmentofthepressure

regulation:

• Turntheturningknob(5)anti-clockwisetill

pressure is fully released

• Connecttheairtoolyouwanttousetothe

quick coupler (6)

• Activatetheairtoolshortly,sothepressure

gauge (7) will show the right pressure level

• Turntheturningknob(5)clockwise,tillthe

pressure gauge (7) shows the pressure level

you need

• Yourairtoolisnowreadytouse.

Note:whennotconnectinganairtoolwhile

adjustingthepressure,itmightoccurthepressure

gauge (7) is not reacting accurately on the

pressure drop.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1045 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 6,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CRM1045 Manual

Product: