538648
8
Zoom out
Zoom in
Previous page
1/48
Next page
Ferm 89
Kompressoren vil ikke slukke
Hvis kompressoren ikke slukkes når det maksimale tryk er opnået, vil sikkerhedventilern på
tanken aktiveres. Det er nødvenligt at kontakte den nærmeste autoriserede support
servicevirksomhed for reparation.
5. VEDLIGEHOLDELSE
Vedligeholdelse
Sørg for, at stikket til maskinen er taget ud af stikkontakten, når der skal udføres
vedligeholdelse på motoren.
Ferm maskiner er blevet konstrueret, så de kan arbejde i længere perioder med et minimum af
vedligeholdelse. Korrekt vedligeholdelse og rengøring af maskinen er en forudsætning for
lang tids tilfredsstillende brug. Før enhver form for vedligeholdelse foretages, sørg altid for at:
Universalknappen er står "0" positionen.
Tryk regulatoren og kontakterne på strømfordelingstavlen er slukket i "0" positionen.
Lufttanken er helt uden tryk.
Rengøring
Kappen omkring motoren skal rengøres med en blød klud, helst hver gang maskinen har været
brugt. Ventilationsrillerne skal holdes fri for støv og snavs. Hvis snavset ikke vil gå af, bruges en
blød klud vredet op i sæbevand. Der må ikke bruges opløsningsmidler som f.eks. benzin, sprit,
salmiakspiritus o.l. Sådanne opløsningsmidler kan beskadige dele af plastic.
Smøring
Det er anbefalet at skille sugefiltret ad hver 50ende driftstime, og rengøre filterelementet ved at
puste det ved lufttryk (fig. 15). Det er anbefalet ar filterelement udskiftes mindst to gange hvert
år hvis kompressoren arbejder i et rent miljø; ofterer hvis arbejdsmiljøet er støvet.
Kompressoren udvikler kondensvand som samles i tanken. Det er nødvendigt at fjerne
kondensvand i tanken mindst én gang om ugen, ved at åbne aftapningshanen (fig. 16) under
tanken. Vær forsigtig når trykluft er i flasken, da vand kan komme ud under stort tryk.
Anbefalet tryk maks. 1-2 Bar.
Kondensvand fra den oliesmurte kompressor bør ikke hældes ud i afløbe,t eller
hældes ud i naturen, da det indeholder olie.
Udskiftning/påfyldning af olie
Kompressoren er leveret med syntetisk olie "SAE 10W30". Det er anbefalet at udskifte alt
pumpesystemets olie inden for de første 100 driftstimer.
Skrue afløbsskruen (pakningen) af på beholderlåget, lad alt olien løbe ud og skrue skruen
på igen (fig. 17).
GB
D
NL
F
E
P
I
S
FIN
N
DK
08
Ferm
Starting up
Check whether the mains voltage corresponds to that indicated on the electrical
specification plate (fig. 10), the permitted tolerance range should be within 5%.
Press the switch situated on the upper part into the "0" position according to the pressure
regulator type fitted on the device (fig. 11).
Put the plug in the plug socket (fig. 9) and start the compressor up by putting the switch of
the pressure regulator in the "I" position. The operation of the compressor is fully
automatic. The pressure regulator will stop the compressor when the maximum value has
been reached and start it up when the pressure drops below the minimum value. Normally
the difference in pressure is approx. 2 Bar/29 psi between the maximum and the minimum
value. For instance - The compressor will stop when it reaches 8 Bar (116 psi) (this is the
maximum operating pressure) and will start up automatically when the pressure within the
tank has dropped to 6 Bar (87 psi).
The head/cylinder/transmission pipe assembly may reach high temperatures, so
take care when working close to these parts and do not touch them to avoid burns
(fig. 12 - 13).
Adjusting the operating pressure
Fig. 14
It is not necessary continuously to use the maximum operating pressure, the compressed-air
tools often require less pressure. With regard to compressors supplied with a pressure
reduction valve it is necessary to set the operating pressureproperly. It is possible to set the
operating pressure by using the turning knob on the reduction valve.
By turning clockwise, the pressure will be increased.
By turning anti-clockwise, the pressurewill be reduced.
The set pressure can be locked by turning the ring under the turning knob in the opposite
direction from the turning knob thereby fixing the turning knob. The set pressure is visible on
the manometer of the reduction valve.
4.FAULTS
Air loss
May be caused by a poor seal of a connection.
Check all connections by wetting them with soap and water.
The compressor runs but does not compress
Fig. 19
May be caused by the valves (C-C2) or a gasket (B1-B2) being broken.
Replace the damaged part.
The compressor will not start
If the compressor is difficult to start, check:
whether the voltage of the mains corresponds to that on the specification plate (fig. 10)
GB
D
NL
F
E
P
I
S
FIN
N
DK
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CRM1028 FCO-1006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1028 FCO-1006 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info