538645
10
Zoom out
Zoom in
Previous page
1/48
Next page
Ferm 87
Ved anvendelse sammen med dette apparat, skal ledningen have et tværsnit på mindst 2.5
mm
2
(dette passer med en maksimal længde på 20 meter). Rul altid forlængerledninger helt ud
før du anvender dem.
Elektriskforbindelse
Sørg altid for om den indgående spænding til motoren stemmer overens med
hovedspændingen vist på typepladen. Kompressoren er udstyret med et elektrisk kabel og et
to-polsstik + jordforbindelse. Det er vigtigt at tilslutte kompressoren til en jordbunden
stikkontakt. (Fig. 9)
Anvend aldrig jordforbindelsen istedet for den neutrale (0-ledning).
Jordforbindelse bør kun anvendes i overenstemmelse med regler for
uheldsforbyggelse
3. ANVENDELSE
Kun til anvendelse i hjemmet
Bemærk: Informationen i denne vejledning er skrevet for at assisterer brugeren i betjening og
vedligeholdelse af kompressoren. Nogle illustrationer i denne vejledning viser detaljer som
kan afvige fra dem på deres kompressor.
Installation
Efter at have udpakket kompressoren (fig. 1) og have checket at den er i god stand og noteret
at ingen skade er sket under transport, bør følgende udføres. Hvis endnu ikke monteret,
montér gummihætten på tanken efter vejledningen fig. 2. Placér kompressoren på en flad
overflade eller på et underlag med maksimum 10° hælning (fig.3), i et godt ventileret rum,
beskyttet mod atmosfæriske faktorer og ikke i spængfarlige omgivelser. Hvis
overfladeområdet er hældende og glat, sørg for at kompressoren ikke bevæger sig under drift.
Hvis overfladen er et bræt eller en hylde på en reol, sørg for at den ikke kan falde ned ved at
sikre den godt. For god ventilation og effektiv afkøling, er det vigtigt at kompressoren er
placeret mindst 100 cm fra væggen (fig. 4).
Sørg for at kompressoren er korrekt transporteret, vend den ikke på hovedet og
løft den ikke med kroge og reb (fig. 5-6).
Vigtigt! Før drift
Fjern plastiklåget fra samledækslet. Fyld beholderen med den leverede olie (250 ml).
Måleinstrumentet i bunden af beholderen indikerer olieniveauet: Dette bør nu være med
niveau med den røde prik (fig. 7 og 8).
Start
Check om hovedspændingen stemmer overens med den som er indikeret på den
elektriske typeplade (fig. 10), den tilladte tolerance rækkevidde bør være inden for 5%.
GB
D
NL
F
E
P
I
S
FIN
N
DK
10 Ferm
Replacing/topping up oil
The compressor has been supplied with synthetic oil "SAE 10W30". It is recommend to fully
replace the oil of the pump system within the first 100 operating hours.
Unscrew the drain plug (gauge) on the sump lid, let all the oil run out and screw back the
plug (fig. 17).
Fill the oil via the upper hole of the sump lid (fig.18) until the level indicated on the gauge
(fig. 8) has been reached.
Check the oil level of the pump system every week and if necessary top up. For operation
under ambient temperatures of -5°C to + 35°C use synthetic oil “SAE 10W30”. The synthetic
oil has the advantage that it does not lose its characteristics, either in summer or in winter
periods.
You should not dispose of the used oil in the sewer or in the environment.
For replacement of oil the table below should be adhered to.
Oil type Operating hours
Multigrade oil SAE 10W30 100 or 6 months
Faults
Should a fault occur, e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find an exploded view showing the parts that can
be ordered.
Environment
To prevent damage during transport, the appliance is delivered in a solid packaging which
consists largely of reusable material. Therefore please make use of options for recycling the
packaging.
Faulty and/or discarded electrical or electronic apparatus have to be collected at
the appropriate recycling locations.
Warranty
The warranty conditions can be found on the separately enclosed warranty card.
GB
D
NL
F
E
P
I
S
FIN
N
DK
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CRM1025 FCO-1524 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CRM1025 FCO-1524 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info