Manual Ferm COM1007P (page 7 of 96) (All languages)

697794

Zoom out

Zoom in

1/96

completely before removing any work piece or

change the settings.

8. Before installing the disc, always inspect the

resin and rubber treated disc for shearing.

9. Always cross-check the maximum operating

speed of the disc cutting saw with the

maximum permitted speed of the motor. Never

exceed the maximum permitted operating

speed indicated on the disc.

10. Never try to mount a disc onto the machine by

force, or to change the size of the axles. Never

use discs which do not fit. Only use discs

which fit the machine.

11. Do not attempt to attach saw blades to the

machine, as it is not designed to cut wood.

12. Do not start cutting until the motor has

reached full speed.

13. If, while operating the machine, the disc no

longer turns or the motor sounds overloaded,

switch off the machine immediately.

14. Keep easily flammable or fragile objects away

from the machine. The machine operator must

avoid letting his or her hands, face or feet

come into contact with the sparks caused

when cutting.

15. Position your machine firmly on a flat, even

surface.

16. Only operate the machine at the voltage stated

on the nameplate.

17. Never touch a sawn-off workpiece, always let

it cool down first.

18. Never attempt to cut workpieces which

exceed the permitted size.

19. During cutting, never position yourself in the

direction of cutting. Always remain to one side.

20. Always leave safety devices installed.

21. Always ensure that you cut slowly and

carefully. Avoid applying the disc to the

workpiece with a jerky motion.

22. Never push the workpiece towards the disc

while holding it in your hands. Always use the

clamp to fix the workpiece.

23. Keep hands away from the cutting disk. Never

cut work pieces where manual support is

needed closer than 15cm from the rotating disk.

24. Make sure the work piece is properly supported

25. Never use cutting fluids. These fluids could

ignite or cause electrical shock

26. Do not cut cast-iron materials

27. Do not cut plastics, wood or synthetic materials

28. Do not cut magnesium

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions. Keep these

instructions in a safe place!

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class II machine – Double insulation –

You don’t need any earthed plug.

Replacing cables or plugs

If the mains cable becomes damaged, it must

be replaced with a special mains cable available

from the manufacturer or the manufacturer’s

customer service. Dispose of old cables or plugs

immediately after replacing them with new ones. It

is dangerous to connect the plug of a loose cable

to a socket.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

2. MACHINE INFORMATION

Intended use

The chop saw has been design for cutting steel

materials in various shapes.

Technical specifications

Mains voltage 220V-240V~

Mains frequency 50Hz

Power input 2.300 W

Rated speed 4.000/min

Saw blade dimensions* Ø 355mm x Ø 25.4mm

Sound pressure L

93 dB(A) K=3

Sound capacity L

105 dB(A) K=3

Vibration a

h, AG

2.90+1.5 m/s2

Weight 15.8kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm COM1007P in the language / languages: All languages as an attachment in your email.

The manual is 10,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm COM1007P Manual

Product: