Manual Ferm CGM1001 (page 8 of 58) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632750

Zoom out

Zoom in

1/58

Ferm 109

Batteriladeren er dobbelt isoleret i overensstemmelse med EN 60335; der

kræves således ingen jording.

Udskiftning af ledninger eller stik

Gamle ledninger og stik skal smides væk, når de er blevet udskiftet med nye. Det er farligt

at sætte stikket på en løs ledning i en stikkontakt.

Isætning og udtagning af batteriet

Fig. B

Kontroller, at batteriet og maskinen er rene og tørre udvendig, før laderen slut-

tes til.

• Sæt batteriet (5) i maskinens fod som vist på tegningen. Tryk på batteriet, indtil det

klikker på plads.

• Tryk på låsepalerne på begge sider (10) før batteriet løsnes og tag det derefter ud af

maskinen.

Start og stop

Fig. 1

Håndtaget er designet med en frigøringsknap for at forhindre opstart ved et uheld.

• Tryk og hold på frigøringsknappen (3), placeret på begge sider af håndtaget, tryk

herefter på hovedkontakten (4)

• Frigør hovedkontakten for at stoppe bladene.

Vælg det blad, der skal bruges

• Det lille græsklipper blad er bedst til at klippe græs omkring træer og andre faste ting

i haven. Kan også bruges til planteskulpturer.

• Det store hækketrimmer blad er bedst til egentlige hække og buske.

Udskiftning af blad

Fig. C

Fjern det genopladelige batteri, før klingerne udskiftes.

Fare for personskade! Bær beskyttelseshandsker!

3. BETJENING

08 Ferm

use tool in conjunction with a residual circuit breaker device.

3) Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alco-

hol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

b. Use safety equipment. Always wear eye protection. Safety equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate con-

ditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in the off position before plugging in.

Carrying power tools with your finger on the switch or plugging in power tools that

have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of these devices can reduce dust

related hazards.

h. Use clamps or a vice to hold work. It’s safer than using your hand and it frees both

hands to operate tool.

4) Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The cor-

rect power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before making any adjustments, chan-

ging accessories, or storing power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamili-

ar with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation. If dama-

ged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cut-

ting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these instructi-

ons and in the manner intended for the particular type of power tool, taking into

account the working conditions and the work to be performed. Use of the power tool

for operations different from intended could result in hazardous situation.

h. Damaged switches must be replaced at a customer service repair centre. Do not use

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CGM1001 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CGM1001 Manual

Product: