763854

Ferm CDM1140 Manual

7
Zoom out
Zoom in
Previous page
1/44
Next page
7
EN
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
For the charger
Intended use
This screwdriver has an integrated lithium-ion
battery, which you can charge with the included USB
charging cable (USB-mains adapter not included).
a) The appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
have been given supervision or instruction
b) Children being supervised not to play with
the appliance
c) Do not recharge non-rechargeable batteries!
d) During charging, batteries must be placed in a
well ventilated area!
e)
Integrated batteries may only be removed
for disposal by qualified personnel. Opening
the housing shell can destroy the power tool.To
remove the battery from the power tool, press the
On/Off switch until the battery is fully discharged.
Unscrew the screws on the housing and remove
the housing shell in order to remove the battery.
To prevent a short circuit, disconnect the
connectors on the battery one at a time and then
isolate the poles. Even when fully discharged, the
battery still contains a residual capacity, which
can be released in case of a short circuit.
Residual risks
Even when the power tool is used as
prescribed it is not possible to eliminate all
residual risk factors. The following hazards
may arise in connection with the power tool’s
construction and design:
a) Health defects resulting from vibration
emission if the power tool is being used
over longer period of time or not adequately
managed and properly maintained.
b) Injuries and damage to property to due to
broken accessories that are suddenly dashed.
Warning! This power tool produces an
electromagnetic field during operation.
This field may under some circumstances
interfere with active or passive medical
implants. To reduce the risk of serious or
fatal injury, we recommend persons with
medical implants to consult their physician
and the medical implant manufacturer
before operating this power tool.
2. MACHINE INFORMATION
Intended use
This screw driver is intended for driving in and
loosening screws.
Technical specifications
Model No CDM1140
Output of charger 5V DC Max. 1000mA
Rechargeable Battery pack 4V Li-ion 320 mAh
Battery charging time 70-90 minutes
Chuck capacity 1/8" (4mm) hex
No load speed 120 /min
Sound pressure level LPA 39.5 dB(A) K=3 dB(A)
Sound power level LWA 50.5 dB(A) K=3 dB(A)
Hand-arm vibration ah
(screw driving without impact) 0.149 m/s2 K=1.5 m/s2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardized test given in
EN62841; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories,
may significantly increase the exposure level.
•
The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1140 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info