762253
8
Zoom out
Zoom in
Previous page
1/40
Next page
8
EN
8. Chuck
9. Gear selection switch
10. Direction switch
11. On / off switch
12. Torque adjustment ring
13. Operation mode ring
14. Work light
15. Side handle
16. Side handle clamp
17. Belt hook
3. OPERATING
Before any work on the power tool,
remove the battery.
The battery must be charged before first
use.
Removing the battery from the machine
Fig. D
1. Hold the machine (1) firmly with one hand
2. Push down the battery unlock button (3)
located on the rear side of the battery (2) with
the other hand.
3. Keep pushing this button (3) down and slide
the battery backwards out of the machine, like
shown in Fig. D.
Inserting the battery into the machine
Fig. D
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
1. Hold the machine (1) firmly with one hand
2. Insert the battery (2) into the base of the
machine as shown in Fig. D.
3. Push the battery further forward until it clicks
into place.
Checking the battery charging status
Fig. A
To check the battery charge status, push and
hold the button (5) on battery.
The battery has 3 LED lights (4) indicating the
charge level, the more lights that burn, the
more charge the battery has left.
When the lights are not burning it means
the battery is empty and must be charged
immediately.
When the machine is not being used over
a longer period of time it is best to store
the battery in charged condition.
Charging the battery with the charger
Fig. E
1. Take the battery (2) from the machine.
2. Turn the battery (2) to upside down position
and slide it onto the charger (6) as shown in
Fig. E.
3. Push the battery (2) until it is fully pushed into
the slot.
4. Plug the charger (6) into an electrical outlet and
wait for a while. The LED indicators (7) on the
charger will lighten up and show the charger
status.
The charger has 2 LED indicators (7) which
indicate the status of the charging process:
Red LED
Status
Green LED
status Charger status
Off Off No power
Off On
Standby mode:
- No battery is inserted or,
- Battery inserted but charging
has finished
On Off Battery charging in Progress
Fully charging the battery may take up to 60
minutes.
After the battery is fully charged remove the
charger plug from the outlet and remove the
battery from the charger.
The battery can be stored or directly installed
on the machine.
Lithium-Ion cells can be stored for a long
period without losing much of their
charge. When the machine is not being
used over a longer period of time it is
best to store the battery in charged
condition.
Assembling the side handle (15)
Fig. C
The side handle (15) can be mounted on the left or
right side of the machine and will provide extra
control when drilling or screw driving.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1138 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1138 in the language / languages: English, Dutch as an attachment in your email.

The manual is 6,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info